Esp32s3 power buck
AlexOpanasevych·beetroot_embedded_course·module5.2/buck-variant/esp32s3_power_buck.kicad_pcb
About the Esp32s3 power buck PCB
Esp32s3 power buck is an open source ESP32 PCB design by AlexOpanasevych, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 90 × 80 mm, with 10 components from 10 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the LM2596S-3.3. By type, the board carries 3 capacitors, 2 ICs, 1 connector, 1 switch, 1 diode and 1 inductor.
It belongs with the power & battery designs in this gallery.
From the project
Module tasks for Beetroot Embedded course
KiCad 10 project: the schematic from Module 5.1 (buck-variant), routed into a 2-layer PCB. This folder is a self-contained copy of the Module 5.1 project (schematic + project files) plus the new, fully routed board (esp32s3powerbuck.kicadpcb`), so it opens as one normal KiCad project.
The board was built programmatically with KiCad's bundled Python/pcbnew (placing real library footprints, creating nets/tracks/vias from the schematic's netlist, and adding the board outline), rather than by hand in the PCB editor - this made it easy to derive exact pad coordinates from the real footprint…
Main components on the Esp32s3 power buck
Esp32s3 power buck bill of materials (BOM)
10 components, 10 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LM2596S-3.3 | TO-263-5_TabPin3 | U1 |
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U2 |
| 1 | Barrel_Jack_5.5x2.1mm | BarrelJack_CUI_PJ-063AH_Horizontal | J1 |
| 1 | SW_Push | SW_PUSH_6mm | SW1 |
| 1 | SS34 | D_SMA | D1 |
| 1 | 33uH | L_10.4x10.4_H4.8 | L1 |
| 1 | 100uF/25V | CP_Radial_D6.3mm_P2.50mm | C1 |
| 1 | 220uF/16V | CP_Radial_D6.3mm_P2.50mm | C2 |
| 1 | 100nF | C_0805_2012Metric | C3 |
| 1 | 10k | R_0805_2012Metric | R1 |
Esp32s3 power buck design files
The KiCad project lives in the AlexOpanasevych/beetroot_embedded_course repository on GitHub; these links point at the commit this page was built from.
Esp32s3 power buck: common questions
What microcontroller does the Esp32s3 power buck use?
The Esp32s3 power buck is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Esp32s3 power buck PCB?
The Esp32s3 power buck measures 90 × 80 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Esp32s3 power buck?
10 components, from 10 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Esp32s3 power buck design files?
From the AlexOpanasevych/beetroot_embedded_course repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Esp32s3 power buck design in my own project?
Yes, under the terms of its GPL-3.0 license, which AlexOpanasevych chose for the repository.
Can I test firmware for the Esp32s3 power buck without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in beetroot_embedded_course
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k