Hatchtrack
anarchyincubator·hatchtrack
About the Hatchtrack PCB
Hatchtrack is an open source ESP32 PCB design by anarchyincubator, published on GitHub under the MIT license. It is a 4-layer board measuring 25.9 × 43.5 mm, with 47 components from 23 distinct parts.
Its main chip is the ESP32-WROOM-32, from the ESP32 family. Other key parts include the CP2102N-A01-GQFN24, LP5912-3.3DRVR, MCP73831T-5ACI/OT, TPD3E001DRLR and BME680. By type, the board carries 16 capacitors, 14 resistors, 7 ICs, 4 diodes, 3 connectors and 2 transistors.
Main components on the Hatchtrack
Hatchtrack bill of materials (BOM)
47 components, 23 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | CP2102N-A01-GQFN24 Silicon Labs | QFN-24-1EP_4x4mm_Pitch0.5mm | U1 |
| 1 | LP5912-3.3DRVR LP5912 TI | WSON-6_2x2mm_Pitch0.65mm | U2 |
| 1 | MCP73831T-5ACI/OT MCP73831 Microchip | SOT-23-5 | U3 |
| 1 | TPD3E001DRLR TPD3E001 TI | TPD3E001_USON_1.45mmx1mm | U4 |
| 1 | BME680 Bosch | BME680 | U5 |
| 1 | ICM-20602 ICM20602 TDK Invensense | PQFN50P300X300X80-16N | U6 |
| 1 | ESP32-WROOM-32 ESP32-WROOM-32U (8M) ESPRESSIF | ESP32-WROOM-32U | U7 |
| 2 | SS8050-G SS8050 ComChip | SOT-23 | Q1, Q2 |
| 1 | 1054431101 USB_A Molex | USB-Micro-B-Molex_105443-1101 | J1 |
| 1 | DNF | SolderWirePad_2x_1mmDrill | J2 |
| 1 | DNF | Pin_Header_Straight_1x06_Pitch1.00mm | J3 |
| 1 | FP11SPA1B1TP00 SW_Push C&K | ButtonPads | SW1 |
| 2 | BAT165E6327HTSA1 BAT-165 Infineon | D_SOD-323 | D1, D5 |
| 1 | APHHS1005CGCK LED Kingbright | LED_0402 | D2 |
| 1 | CLV1L-FKB-CHMMQEHBB7673673 CREE_LED_RGB Cree | PLCC4 | D3 |
| 6 | GRM155R61A475MEAAD 4.7uF Murata | C_0402 | C1, C2, C7, C9, C11, C16 |
| 3 | CC0402KRX5R6BB105 1uF Yageo | C_0402 | C3, C5, C6 |
| 7 | GRM155R61C104KA88D 0.1uF Murata | C_0402 | C4, C8, C10, C12, C13, C14, C15 |
| 5 | ERJ-2RKF1001X 1K Panasonic | R_0402 | R1, R3, R9, R10, R11 |
| 1 | ERJ-2RKF5601X 5.6k Panasonic | R_0402 | R2 |
Show 3 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 5 | ERJ-2RKF1002X 10K Panasonic | R_0402 | R4, R5, R6, R7, R8 |
| 2 | ERJ-2GE0R00X 0 Panasonic | R_0402 | R12, R13 |
| 1 | ERJ-2GE0R00X 10K Panasonic | R_0402 | R14 |
Hatchtrack design files
The KiCad project lives in the anarchyincubator/hatchtrack repository on GitHub; these links point at the commit this page was built from.
Hatchtrack: common questions
What microcontroller does the Hatchtrack use?
The Hatchtrack is built around the ESP32-WROOM-32, from the ESP32 family.
How big is the Hatchtrack PCB?
The Hatchtrack measures 25.9 × 43.5 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Hatchtrack?
47 components, from 23 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Hatchtrack design files?
From the anarchyincubator/hatchtrack repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the Hatchtrack design in my own project?
Yes, under the terms of its MIT license, which anarchyincubator chose for the repository.
Can I test firmware for the Hatchtrack without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k