Iontophoresis-Device

apotatoa·Iontophoresis-Device·hardware/Ionto.kicad_pcb

Iontophoresis-Device PCB layout, top view — open source ESP32 board by apotatoa

About the Iontophoresis-Device PCB

Iontophoresis-Device is an open source ESP32 PCB design by apotatoa, published on GitHub under the GPL-2.0 license. It is a 6-layer board measuring 100 × 97.8 mm, with 54 components from 40 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the AP63203WU, AG7200, LM358DT and PC817. By type, the board carries 14 resistors, 12 capacitors, 5 ICs, 5 connectors, 5 switches and 4 diodes.

It belongs with the displays & leds and power & battery designs in this gallery.

From the project

An open source iontophoresis device prototyped with Phase Dock Inc's WorkBench platform

Galvanic Isolation is mandatory: Never bypass the isolation barriers designed into this PCB. Battery Power Only: This device is designed solely for battery operation. Educational Use: This project is for educational and research purposes only. It is not an FDA-approved medical device. Liability: The authors and contributors are not responsible for any harm caused by the assembly or use of this device. Build and use at your own risk.

Main components on the Iontophoresis-Device

Iontophoresis-Device bill of materials (BOM)

54 components, 40 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
AP63203WU
U2
1
ESP32-S3-WROOM-1
U3
1
AG7200
Ag7200
U4
1
LM358DT
U5
1
PC817
U6
2
2N3904
Q1, Q2
1
IRF540N
Q3
1
CONN_01X02_PIN
Conn_01x02_Pin
J1
1
CONN_01X04_PIN
Conn_01x04_Pin
J2
1
USB_C_RECEPTACLE_USB2.0_14P
USB_C_Receptacle_USB2.0_14P
J3
1
CONN_01X01
Conn_01x01
J4
1
CONN_01X01
Conn_01x01
J5
1
Fuse
50mA1
1
Buzzer
BZ1
2
SANYOU_SRD_Form_C
K1, K2
1
250K
250k
RV1
1
SW_WUERTH_450301014042
SW_Wuerth_450301014042
SW1
1
Reset
SW2
1
Enter
SW3
1
Inc+
SW4
Show 20 more
QtyPartRefs
1
Dec-
SW5
1
SMAJ58A
D1
2
1N4148
D2, D3
1
1N4742A/12V/1W
1N4742A/12v/1w
D4
1
4.7UH
4.7uH
L1
1
100NF
100nF
C1
1
10UF
10uF
C2
2
22UF
22uF
C3, C4
4
1UF
1uF
C5, C6, C7, C8
1
47UF/63V
47uF/63v
C9
1
10UF/25V
10uF/25v
C10
1
1UF
1uF
C11
1
.1uF
C12
1
330
R1
2
5.1K
5.1k
R2, R3
5
10K
10k
R4, R5, R6, R7, R13
3
1k
R8, R9, R10
1
100Ω/1w
R11
1
5.6K/0.5W
5.6k/0.5w
R12
1
4.7K
4.7k
R14

Iontophoresis-Device design files

The KiCad project lives in the apotatoa/Iontophoresis-Device repository on GitHub; these links point at the commit this page was built from.

Iontophoresis-Device: common questions

What microcontroller does the Iontophoresis-Device use?

The Iontophoresis-Device is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Iontophoresis-Device PCB?

The Iontophoresis-Device measures 100 × 97.8 mm, has 6 copper layers and is 1.6 mm thick.

How many components are on the Iontophoresis-Device?

54 components, from 40 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Iontophoresis-Device design files?

From the apotatoa/Iontophoresis-Device repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Iontophoresis-Device design in my own project?

Yes, under the terms of its GPL-2.0 license, which apotatoa chose for the repository.

Can I test firmware for the Iontophoresis-Device without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards