HLF-MIDI
AwesomeSno·HLF-MIDI·kicad/hlf_midi.kicad_pcb
About the HLF-MIDI PCB
HLF-MIDI is an open source ESP32 PCB design by AwesomeSno, published on GitHub. It is a 2-layer board measuring 180 × 75 mm, with 18 components from 8 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6 and TLV75533PDBVR. By type, the board carries 8 LEDs, 4 switches, 3 ICs and 1 connector.
It belongs with the audio, keyboards and displays & leds designs in this gallery.
From the project
LET'S MAKE MUSICCC
A super slim, solid-state MIDI keyboard built with an ESP32-S3 that uses capacitive touch pads instead of mechanical switches. It plugs straight into any laptop, phone, or DAW as a plug-and-play USB-MIDI device.
Traditional MIDI keyboards are usually pretty bulky, full of plastic mechanisms, and annoying to carry around. For Hack Club's Half Life, I wanted to build something super flat and minimal: a solid-state MIDI keyboard with zero moving key parts, where the keys are literally etched onto the PCB in gold (ENIG).

Main components on the HLF-MIDI
HLF-MIDI bill of materials (BOM)
18 components, 8 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | USBLC6-2SC6 | SOT-23-6 | U2 |
| 1 | TLV75533PDBVR | SOT-23-5 | U3 |
| 1 | TYPE-C-31-M-12 | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | EC11E15244G1 EC11_Knob | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | ENC1 |
| 1 | PTA4543-2015DPB103 | Potentiometer_Bourns_PTA4543_Single_Slide | RV1 |
| 4 | TL3342F160QG | SW_SPST_TL3342 | SW1, SW2, SW3, SW4 |
| 8 | SK6812MINI-E | LED_SK6812MINI-E | LED1, LED2, LED3, LED4, LED5, LED6, LED7, LED8 |
HLF-MIDI design files
The KiCad project lives in the AwesomeSno/HLF-MIDI repository on GitHub; these links point at the commit this page was built from.
- Layoutkicad/hlf_midi.kicad_pcb
- Schematickicad/hlf_midi.kicad_sch
- BOMkicad/bom.csv
HLF-MIDI: common questions
What microcontroller does the HLF-MIDI use?
The HLF-MIDI is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the HLF-MIDI PCB?
The HLF-MIDI measures 180 × 75 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the HLF-MIDI?
18 components, from 8 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the HLF-MIDI design files?
From the AwesomeSno/HLF-MIDI repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the HLF-MIDI design in my own project?
The repository has no license, so all rights stay with AwesomeSno. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the HLF-MIDI without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k