Pic32mx jtag
About the Pic32mx jtag PCB
Pic32mx jtag is an open source PIC PCB design by azonenberg, published on GitHub under the BSD-3-Clause license. It is a 4-layer board measuring 73 × 54 mm, with 36 components from 16 distinct parts.
Its main chip is the PIC32MX6xxFxxxH, from the PIC family. Other key parts include the LDO1117-33_SOT223. By type, the board carries 11 capacitors, 10 connectors, 9 resistors, 4 diodes and 2 ICs.
It belongs with the dev boards & breakouts and usb & debug tools designs in this gallery.
From the project
Miscellaneous prototype hardware that wasn't major enough to warrant a dedicated repo
Main components on the Pic32mx jtag
Pic32mx jtag bill of materials (BOM)
36 components, 16 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | PIC32MX6xxFxxxH | QFP_64_0.5MM | U1 |
| 1 | LDO1117-33_SOT223 | SOT223-4 | U2 |
| 1 | BARREL_JACK | CONN_CUI_PJ-058BH_HIPWR_BARREL_NOSLOT | J1 |
| 1 | CONN_01X05 | CONN_HEADER_2.54MM_1x5 | J2 |
| 4 | PMOD_HOST | CONN_HEADER_2.54MM_2x6_RA_PMOD_HOST | J3, J4, J5, J7 |
| 1 | XILINX_JTAG | XILINX_JTAG_PTH_MOLEX_0878311420 | J6 |
| 1 | CONN_01X03 | CONN_HEADER_2.54MM_1x3 | J8 |
| 2 | U.FL | CONN_U.FL_TE_1909763-1 | J9, J10 |
| 4 | GREEN | EIA_0805_LED | D1, D2, D3, D4 |
| 3 | 4.7 uF | EIA_0603_CAP_NOSILK | C1, C3, C9 |
| 6 | 0.47 uF | EIA_0402_CAP_NOSILK | C2, C4, C6, C8, C10, C11 |
| 1 | 10 uF | EIA_0805_CAP_NOSILK | C5 |
| 1 | 0.1 uF | EIA_0402_CAP_NOSILK | C7 |
| 5 | 470 | EIA_0402_RES_NOSILK | R1, R6, R7, R8, R9 |
| 1 | 10K | EIA_0402_RES_NOSILK | R2 |
| 3 | 33 | EIA_0402_RES_NOSILK | R3, R4, R5 |
Pic32mx jtag design files
The KiCad project lives in the azonenberg/misc-devboards repository on GitHub; these links point at the commit this page was built from.
Pic32mx jtag: common questions
What microcontroller does the Pic32mx jtag use?
The Pic32mx jtag is built around the PIC32MX6xxFxxxH, from the PIC family.
How big is the Pic32mx jtag PCB?
The Pic32mx jtag measures 73 × 54 mm, has 4 copper layers and is 1.737 mm thick.
How many components are on the Pic32mx jtag?
36 components, from 16 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pic32mx jtag design files?
From the azonenberg/misc-devboards repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Pic32mx jtag design in my own project?
Yes, under the terms of its BSD-3-Clause license, which azonenberg chose for the repository.
Can I test firmware for the Pic32mx jtag without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug PIC firmware against it before you order a PCB.
More boards in misc-devboards
STM32Kup lulz
154.5 × 137 mm376 parts4LBSD-3-Clause17
STM32Fpga stm32-ifaces
90 × 94.5 mm267 parts6LBSD-3-Clause17
STM32Baset1-media converter
100.5 × 62.5 mm173 parts4LBSD-3-Clause17
Ksz9031-eval
77 × 71.5 mm167 parts4LBSD-3-Clause17
FPGAFpga test kintex676-artix484
73 × 88 mm152 parts4LBSD-3-Clause17
Lpr rgmii phy
35 × 73.5 mm82 parts4LBSD-3-Clause17
Tragiclaser phy
105 × 28.5 mm79 parts4LBSD-3-Clause17
Ltc3374-test
74 × 58 mm71 parts4LBSD-3-Clause17
STM32Christmas tree
66 × 93.5 mm61 parts2LBSD-3-Clause17
STM32T20-l431-som
10.1 × 12.2 mm54 parts4LBSD-3-Clause17
Qsfp to arc6
90 × 43 mm37 parts4LBSD-3-Clause17
Similar boards
PICPslab hardware
fossasia
99 × 53.3 mm187 parts4LApache-2.01.7k
PICMicro 8088
skiselev
152.4 × 101.6 mm71 partsGPL-3.0414
PICGB-CARTPP-DIY
Gekkio
100 × 100 mm22 parts2LCC-BY-4.0376
PICGB-BENCH-G1
100 × 100 mm98 parts4LCC-BY-4.0376
PICGB-MBCTEST
51.4 × 61 mm32 parts2LCC-BY-4.0376
PICGB-LIVE32
51.4 × 61 mm46 parts4LCC-BY-4.0376