Esp32-lora gps tracker

bogdan-kovalchuk·esp32-lora-gps-tracker·hardware/lora-gps-tracker-rev-a/lora-gps-tracker-rev-a.kicad_pcb

Esp32-lora gps tracker PCB layout, top view — open source ESP32 board by bogdan-kovalchuk

About the Esp32-lora gps tracker PCB

Esp32-lora gps tracker is an open source ESP32 PCB design by bogdan-kovalchuk, published on GitHub under the MIT license. It is a 4-layer board measuring 65 × 45 mm, with 63 components from 39 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the TLV75733PDBVR, TP4056-42-ESOP8 (SOP-8-PP), TPS3808G33DBVR, USBLC6-2SC6 and Ra-02. By type, the board carries 24 resistors, 17 capacitors, 7 ICs, 5 connectors, 4 switches and 4 diodes.

It belongs with the rf & radio, power & battery and iot & wireless designs in this gallery.

From the project

Encrypted point-to-point GPS telemetry over 433 MHz LoRa between two ESP32 boards.

Encrypted point-to-point GPS telemetry over 433 MHz LoRa between two ESP32 boards.

- PlatformIO CLI or VS Code with the PlatformIO extension - GCC toolchain (only required to run native protocol tests)

- Separate transmitter and receiver firmware - Position, altitude, speed, course, satellites, HDOP, UTC date/time - AES-256-GCM authenticated encryption - Versioned 72-byte binary packets with CRC16 and replay detection - RSSI / SNR reporting on the receiver - Demo mode for radio testing without a GPS module

Main components on the Esp32-lora gps tracker

TLV75733PDBVRTP4056-42-ESOP8 (SOP-8-PP)ESP32-S3-WROOM-1-N16R8TPS3808G33DBVRUSBLC6-2SC6Ra-02GNSS LCC18 (see table)

Esp32-lora gps tracker bill of materials (BOM)

63 components, 39 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TLV75733PDBVR
Texas Instruments
U101
1
TP4056-42-ESOP8 (SOP-8-PP)
TP4056
NanJing Top Power
U102
1
ESP32-S3-WROOM-1-N16R8 (or N16 / N8, same footprint; owner W06)
ESP32-S3-WROOM-1-N16R8
Espressif
U201
1
TPS3808G33DBVR
Texas Instruments
U202
1
USBLC6-2SC6
STMicroelectronics
U203
1
Ra-02
Ai-Thinker
U301
1
ATGM336H-5N31 or LC76GABMD (first boards); MAX-M10S-00B or L76KB-A58 on the same land
GNSS LCC18 (see table)
Zhongke / Quectel / u-blox
U401
1
S2B-PH-K-S(LF)(SN)
BATT
JST
J101
1
TYPE-C-31-M-12
HRO
J201
1
PZ254V-11-06P
UART0
XFCN
J202
1
U.FL-R-SMT-1(10); antenna (off-board, buy separately): active GNSS patch 18x18 or 25x25 mm WITH SAW pre-filter before its LNA, 3.3 V supply, gain <= 30 dB, 5-10 cm U.FL cable
U.FL
Hirose
J401
1
PZ254V-11-06P
EXP
XFCN
J501
1
1206L150THWR
1.5A hold
Littelfuse
F101
1
PCM12SMTR (SPDT slide, signal current only)
POWER
C&K
SW101
1
TS-1187A-B-A-B
RESET
XKB Connectivity
SW201
1
TS-1187A-B-A-B
BOOT
XKB Connectivity
SW202
1
TS-1187A-B-A-B
USER
XKB Connectivity
SW501
1
SMF6.0A (unidirectional, VRWM 6.0 V, VC about 10.3 V)
SMF6.0A
Littelfuse / Vishay
D101
1
KT-0603R
RED
Hubei KENTO Elec
D103
1
FYLS-0603GD
GREEN
Foryard
D201
Show 19 more
QtyPartRefs
1
blue 0603 LED with VF <= 2.9 V at 2 mA (e.g. KT-0603B; check VF on the purchased part)
BLUE
Hubei KENTO Elec
D501
1
LQW18AN47NG00 (0603 wirewound; L1 bias choke >= 47 nH per Quectel L76 HD)
47nH
Murata
L401
6
CL21A106KAYNNNE
10uF
Samsung
C101, C102, C105, C106, C301, C407
8
CC0603KRX7R9BB104
100nF
Yageo
C104, C202, C203, C204, C205, C302, C405, C408
1
CL21A226MAQNNNE
22uF
Samsung
C201
1
0603B103K500NT
10nF
FH
C401
1
CC0603JRNPO9BN101
100pF
Yageo
C402
1
0603WAF2401T5E
2.4k
UNI-ROYAL
R101
2
0603WAF1001T5E
1k
UNI-ROYAL
R104, R209
3
0603WAF1003T5E
100k
UNI-ROYAL
R105, R115, R406
2
0603WAF1004T5E
1M
UNI-ROYAL
R111, R112
4
0603WAF1002T5E
10k
UNI-ROYAL
R201, R202, R301, R501
2
0603WAF5101T5E
5.1k
UNI-ROYAL
R203, R204
2
0603WAF220JT5E
22
UNI-ROYAL
R205, R206
1
0603WAF4990T5E
499
UNI-ROYAL
R207
3
0603WAF4701T5E
4.7k
UNI-ROYAL
R208, R503, R504
2
0603WAF0000T5E
0
UNI-ROYAL
R401, R403
1
1206W4F150JT5E (15 R, 1206, 0.25 W)
15
UNI-ROYAL
R402
1
0603WAF1000T5E
100
UNI-ROYAL
R502

Esp32-lora gps tracker design files

The KiCad project lives in the bogdan-kovalchuk/esp32-lora-gps-tracker repository on GitHub; these links point at the commit this page was built from.

Esp32-lora gps tracker: common questions

What microcontroller does the Esp32-lora gps tracker use?

The Esp32-lora gps tracker is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the Esp32-lora gps tracker PCB?

The Esp32-lora gps tracker measures 65 × 45 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Esp32-lora gps tracker?

63 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Esp32-lora gps tracker design files?

From the bogdan-kovalchuk/esp32-lora-gps-tracker repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Esp32-lora gps tracker design in my own project?

Yes, under the terms of its MIT license, which bogdan-kovalchuk chose for the repository.

Can I test firmware for the Esp32-lora gps tracker without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards