Elevator
Bruhdows·klink·hardware/electronics/elevator/elevator.kicad_pcb
About the Elevator PCB
Elevator is an open source AVR/Arduino PCB design by Bruhdows, published on GitHub. It is a 4-layer board measuring 60 × 44 mm, with 47 components from 30 distinct parts.
Its main chip is the ATTINY404-SSN, from the AVR/Arduino family. Other key parts include the LMR36510ADDAR, AP2112K-3.3TRG1 and DRV8876PWPR. By type, the board carries 20 resistors, 15 capacitors, 5 connectors, 4 ICs, 2 diodes and 1 inductor.
It belongs with the sensors designs in this gallery.
From the project
Klink is an 80x80mm magnetic tile system for programmable marble runs. V1 keeps sixteen identical intelligent tiles, a six-port Hub, removable modules and a motorized elevator for continuous circulation. Sensors, buttons, RGB LEDs and a gate let a program react to marbles and peo
Klink is an 80x80mm magnetic tile system for programmable marble runs. V1 keeps sixteen identical intelligent tiles, a six-port Hub, removable modules and a motorized elevator for continuous circulation. Sensors, buttons, RGB LEDs and a gate let a program react to marbles and people.
The design is in progress. It is not ready for main-board fabrication or Fallen Design Submission. The remaining digital work and physical qualification gates are listed below.

Main components on the Elevator
Elevator bill of materials (BOM)
47 components, 30 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | LMR36510ADDAR | TI_SO-PowerPAD-8 | U1 |
| 1 | AP2112K-3.3TRG1 | SOT-23-5 | U2 |
| 1 | DRV8876PWPR | TI_PWP0016A_Mask3.3x3.3 | U3 |
| 1 | ATTINY404-SSN ATtiny404-SSN | SOIC-14_3.9x8.7mm_P1.27mm | U4 |
| 1 | TSW-108-07-G-S MODULE_SERVICE | PinHeader_1x08_P2.54mm_Vertical | J1 |
| 1 | TSW-102-07-G-S MOTOR | PinHeader_1x02_P2.54mm_Vertical | J2 |
| 1 | TSW-102-07-G-S STOP_NC | PinHeader_1x02_P2.54mm_Vertical | J3 |
| 1 | TSW-104-07-G-S INDEX_SENSOR | PinHeader_1x04_P2.54mm_Vertical | J4 |
| 1 | TSW-103-07-G-S UPDI | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | SMBJ13A-E3/52 | D_SMB | D1 |
| 1 | BAT54S,215 | SOT-23 | D2 |
| 1 | SRP7050TA-330M 33uH | L_Bourns_SRP7050TA | L1 |
| 1 | C3216X7R1H106K160AC 10uF 50V X7R | C_1206_3216Metric | C1 |
| 5 | C2012X7R1H104K125AE 100nF 50V X7R | C_0805_2012Metric | C2, C9, C10, C12, C13 |
| 2 | C2012X7R1H105K125AB 1uF 16V | C_0805_2012Metric | C3, C7 |
| 2 | C1210C226K3RACTU 22uF 25V X7R | C_1210_3225Metric | C4, C5 |
| 1 | EEH-ZC1E101XP 100uF 25V | CP_Elec_6.3x7.7 | C6 |
| 1 | C2012X7R1C475K125AB 4.7uF 16V | C_0805_2012Metric | C8 |
| 1 | C2012C0G1H223J125AA 22nF 50V | C_TDK_C2012_Reflow | C11 |
| 2 | CC0805KRX7R9BB103 10nF 16V | C_0805_2012Metric | C14, C15 |
Show 10 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | RC0805FR-0722KL 22k 1% | R_0805_2012Metric | R1, R17 |
| 6 | RC0805FR-07100KL 100k 1% | R_0805_2012Metric | R2, R10, R11, R12, R13, R14 |
| 3 | RC0805FR-0710KL 10k 1% | R_0805_2012Metric | R3, R9, R18 |
| 1 | RT0805BRD07110KL 110k 0.1% | R_0805_2012Metric | R4 |
| 2 | RT0805BRD0710KL 10k 0.1% | R_0805_2012Metric | R5, R7 |
| 1 | RT0805BRD0723K2L 23.2k 0.1% | R_0805_2012Metric | R6 |
| 1 | RT0805BRD072K87L 2.87k 0.1% | R_0805_2012Metric | R8 |
| 2 | RC0805FR-071KL 1k 1% | R_0805_2012Metric | R15, R20 |
| 1 | RC0805FR-07150KL 150k 1% | R_0805_2012Metric | R16 |
| 1 | RC1206FR-07150RL 150 1% 0.25W | R_1206_3216Metric | R19 |
Elevator design files
The KiCad project lives in the Bruhdows/klink repository on GitHub; these links point at the commit this page was built from.
Elevator: common questions
What microcontroller does the Elevator use?
The Elevator is built around the ATTINY404-SSN, from the AVR/Arduino family.
How big is the Elevator PCB?
The Elevator measures 60 × 44 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Elevator?
47 components, from 30 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Elevator design files?
From the Bruhdows/klink repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Elevator design in my own project?
The repository has no license, so all rights stay with Bruhdows. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Elevator without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug AVR/Arduino firmware against it before you order a PCB.
More boards in klink
STM32
Hub
Bruhdows
148 × 78 mm309 parts4LNo license1WCH CH32/CH55x
Tile
Bruhdows
68 × 68 mm109 parts4LNo license1Side contact test
Bruhdows
40 × 28 mm15 parts2LNo license1Side flat test
Bruhdows
40 × 12 mm15 parts2LNo license1Marble sensor
Bruhdows
50 × 36 mm11 parts2LNo license1Flat contact test
Bruhdows
20 × 12 mm6 parts2LNo license1Spring contact test
Bruhdows
20 × 12 mm6 parts2LNo license1Gate
Bruhdows
40 × 30 mm5 parts2LNo license1Button
Bruhdows
40 × 30 mm4 parts2LNo license1
Similar boards
AVR/Arduino
Magspoof
samyk
35 × 29 mm11 parts2LNo license4.2kAVR/Arduino
Redox keyboard
mattdibi
162.2 × 126.5 mm77 parts2LMIT2.0kAVR/Arduino
Labrador
espotek-org
36.8 × 34.7 mm75 parts2LNo license1.2kAVR/Arduino
ModuleV450
stuartpittaway
30 × 61.4 mm39 parts2LCC-BY-NC-4.01.1kAVR/Arduino
V4
stuartpittaway
30 × 50 mm38 parts2LCC-BY-NC-4.01.1kAVR/Arduino
Discipline
coseyfannitutti
304.9 × 122.8 mm170 parts2LCC-BY-NC-4.01.0k