22 open source boards using the LMR36510ADDAR

Real designs built with the LMR36510ADDAR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.

22 boardsClear filters|Most starred

How designs wire the LMR36510ADDAR

Read from the KiCad layouts of 13 open source designs, one per repository: what each pin of the LMR36510ADDAR connects to, and the resistors, capacitors and other passives placed on it.

  • The FB_5 pin has a resistor to GND on 12 of 13 designs, most often 20 kΩ (then 43.2 kΩ).
  • The VCC_6 pin has a capacitor to GND on 12 of 13 designs, most often 1 µF.
  • The BOOT_7 pin has a series capacitor on 12 of 13 designs, most often 100 nF.
  • The SW_8 pin has a series capacitor on 12 of 13 designs, most often 100 nF.
PGND_1pin 1Connected to: GND 92%
VIN_2pin 2Connected to: VIN_PROT 46% · a signal 46%
  • Capacitor to GND on 85% · 100 nF (6), 2.2 µF (5), 10 µF (5)
EN_3pin 3Connected to: Signal 54% · VIN 38%
  • Capacitor to GND on 69% · 100 nF (6), 10 µF (4), 2.2 µF (3)
  • Resistor to GND on 31% · 100 kΩ (2), 10 kΩ (1), 33 kΩ (1)
PG_4pin 4Connected to: Not connected 77% · a signal 15%
FB_5pin 5Connected to: Signal 92%
  • Resistor to GND on 92% · 20 kΩ (4), 43.2 kΩ (2), 24.9 kΩ (2)
  • Pull-up to 5V on 54% · 100 kΩ (4), 47 kΩ (2), 80.6 kΩ (1)
  • Series resistor on 38% · 100 kΩ (2), 110 kΩ (1), 120 kΩ (1)
VCC_6pin 6Connected to: Signal 77% · 10V 15%
  • Capacitor to GND on 92% · 1 µF (12)
BOOT_7pin 7Connected to: Signal 100%
  • Series capacitor on 92% · 100 nF (12)
SW_8pin 8Connected to: Signal 92%
  • Series capacitor on 92% · 100 nF (12)
  • Inductor on 92% · 22 µH (7), 33 µH (1), 15 µH (1)
PAD_9pin 9Connected to: GND 92%

Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Chatgpt astra test2 by fredriknk, Elevator by Bruhdows, BMS-Master-STM32-Nucleo-G474RE by gabrielfbdiniz and Esp32-solar attic fan controller by alex1klimovich.

The LMR36510ADDAR in open source designs

The gallery holds 22 open source boards using the LMR36510ADDAR from 13 GitHub repositories; a typical one measures about 95 × 74 mm and carries around 73 components.

82% use four copper layers or more, and 55% carry an open source license.

The most starred is Chatgpt astra test2 by fredriknk.

Microcontrollers on boards using the LMR36510ADDAR

LMR36510ADDAR: common questions

Where can I find a LMR36510ADDAR reference design?

Each of the 22 boards on this page is a real design using the LMR36510ADDAR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.

What resistor goes on the LMR36510ADDAR FB_5 pin?

The FB_5 pin has a resistor to GND on 12 of 13 designs, most often 20 kΩ (then 43.2 kΩ). Counted from the KiCad layouts of 13 open source designs using the LMR36510ADDAR.

How is the LMR36510ADDAR VCC_6 pin connected?

The VCC_6 pin has a capacitor to GND on 12 of 13 designs, most often 1 µF. Counted from the KiCad layouts of 13 open source designs using the LMR36510ADDAR.

How is the LMR36510ADDAR BOOT_7 pin connected?

The BOOT_7 pin has a series capacitor on 12 of 13 designs, most often 100 nF. Counted from the KiCad layouts of 13 open source designs using the LMR36510ADDAR.

What parts are used alongside the LMR36510ADDAR?

The USBLC6-2SC6, AP2112K-3.3TRG1, ESP32-S3-WROOM-1-N8R8, ADM2587EBRWZ-REEL7 and ADS1115IDGSR appear in the most repositories here.

Which microcontrollers do boards using the LMR36510ADDAR use?

Most are built on ESP32 (11), NXP (3), STM32 (2) and AVR/Arduino (1).

How big is a typical board using the LMR36510ADDAR?

The median is 95 × 74 mm, and 18% are two-layer designs.

What is the most popular open source board using the LMR36510ADDAR?

By GitHub stars, Chatgpt astra test2 by fredriknk, with 3 stars.

Can I simulate one of these boards using the LMR36510ADDAR before building it?

Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.

Browse boards by part