11 open source boards using the DRV8876PWPR
Real designs built with the DRV8876PWPR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
Tsumikoro Servo Controller
theatrus
62 × 45 mm63 parts4LCERN-OHL-P-2.01- schematic only · 38 parts
Epicura spec
manasXP
38 partsNo license1 Phmod
gallicchio
100 × 100 mm234 parts4LCERN-OHL-P-2.00ESP32
Controller core reva
itorralbo
141.6 × 135.2 mm187 parts4LMIT0ESP32
Maslow Mini Merged Board
BarbourSmith
70.7 × 111 mm156 parts4LNo license0ESP32
Smart latch lock
RobbyV2
45 × 34 mm63 parts4LNo license0STM32
Motormodul
Meo98
75 × 65 mm63 parts2LGPL-3.00STM32
Haptic linear slider
jdelgranchio
130.5 × 46 mm62 parts2LNo license0ESP8266
Gate controller
eranknafo2001
45.5 × 33 mm21 parts2LNo license0AVR/Arduino
Elevator
Bruhdows
60 × 44 mm47 parts4LNo license1ESP32
Four Motor Control Board M5 fbc631ad57bc4ffbb8f9b332692f9e33
BarbourSmith
70.7 × 111 mm82 parts4LNo license0
How designs wire the DRV8876PWPR
Read from the KiCad layouts of 9 open source designs, one per repository: what each pin of the DRV8876PWPR connects to, and the resistors, capacitors and other passives placed on it.
- The CPH_13 pin has a series capacitor on 9 of 9 designs, most often 22 nF.
- The CPL_14 pin has a series capacitor on 9 of 9 designs, most often 22 nF.
- The IPROPI_6 pin has a resistor to GND on 8 of 9 designs, most often 1.5 kΩ (then 2.49 kΩ).
- The FAULT_4 pin has a pull-up to 3.3V on 6 of 9 designs, most often 10 kΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| EN/IN1_1pin 1 | Connected to: The microcontroller 67%, a connector 22% |
|
| PH/IN2_2pin 2 | Connected to: The microcontroller 67%, a connector 22% |
|
| FAULT_4pin 4 | Connected to: The microcontroller 56% · not connected 33% |
|
| VREF_5pin 5 | Connected to: 3.3V 44% · a signal 44% |
|
| IPROPI_6pin 6 | Connected to: The microcontroller 33% |
|
| IMODE_7pin 7 | Connected to: GND 67% · a signal 33% |
|
| PGND_9pin 9 | Connected to: GND 100% | — |
| VM_11pin 11 | Connected to: 24V 67% · a signal 33% |
|
| VCP_12pin 12 | Connected to: Signal 100% |
|
| CPH_13pin 13 | Connected to: Signal 100% |
|
| CPL_14pin 14 | Connected to: Signal 100% |
|
| GND_15pin 15 | Connected to: GND 100% | — |
| EP_17pin 17 | Connected to: GND 100% | — |
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Elevator by Bruhdows, Tsumikoro Servo Controller by theatrus, Four Motor Control Board M5 fbc631ad57bc4ffbb8f9b332692f9e33 by BarbourSmith and Gate controller by eranknafo2001.
The DRV8876PWPR in open source designs
The gallery holds 11 open source boards using the DRV8876PWPR from 10 GitHub repositories; a typical one measures about 70.7 × 55.5 mm and carries around 63 components.
70% use four copper layers or more, and 36% carry an open source license.
The most starred is Tsumikoro Servo Controller by theatrus.
Parts used alongside the DRV8876PWPR
Microcontrollers on boards using the DRV8876PWPR
What boards using the DRV8876PWPR are built for
DRV8876PWPR: common questions
Where can I find a DRV8876PWPR reference design?
Each of the 11 boards on this page is a real design using the DRV8876PWPR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the DRV8876PWPR CPH_13 pin connected?
The CPH_13 pin has a series capacitor on 9 of 9 designs, most often 22 nF. Counted from the KiCad layouts of 9 open source designs using the DRV8876PWPR.
How is the DRV8876PWPR CPL_14 pin connected?
The CPL_14 pin has a series capacitor on 9 of 9 designs, most often 22 nF. Counted from the KiCad layouts of 9 open source designs using the DRV8876PWPR.
What resistor goes on the DRV8876PWPR IPROPI_6 pin?
The IPROPI_6 pin has a resistor to GND on 8 of 9 designs, most often 1.5 kΩ (then 2.49 kΩ). Counted from the KiCad layouts of 9 open source designs using the DRV8876PWPR.
Which microcontrollers do boards using the DRV8876PWPR use?
Most are built on ESP32 (4), STM32 (3), AVR/Arduino (1) and ESP8266 (1).
How big is a typical board using the DRV8876PWPR?
The median is 70.7 × 55.5 mm, and 30% are two-layer designs.
What is the most popular open source board using the DRV8876PWPR?
By GitHub stars, Tsumikoro Servo Controller by theatrus, with 1 stars.
Can I simulate one of these boards using the DRV8876PWPR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.