Routing candidate1

c-lydia·SmartDB·smart_db_v2/smart_db/work/routing_candidate1.kicad_pcb

Routing candidate1 PCB layout, top view — open source ESP32 board by c-lydia

About the Routing candidate1 PCB

Routing candidate1 is an open source ESP32 PCB design by c-lydia, published on GitHub under the Apache-2.0 license. It is a 4-layer board measuring 95 × 78 mm, with 73 components from 50 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the ADS1115IDGS, AP63203WU-7 and CP2102N-A02-GQFN28. By type, the board carries 27 resistors, 21 capacitors, 8 diodes, 5 connectors, 4 ICs and 2 transistors.

From the project

A distribution board system designed for automatic electrical fault monitoring using Digital Signal Processing (FFT analysis), Isolation Forest, and YOLO thermal imaging detection with a Mobile App, alerting system, and automatic cutoff.

Updated 2026-10-10. Fully routed bench prototype; fabrication review remains.

Open smartdb.kicadpro in KiCad. The editable schematic, PCB, project-local symbol and footprint libraries are saved together here. This is the permanent v2 project, moved from ../compactwip/`. The previous routed bench revision and its reports are preserved in the archive.

- Draft 95 × 78 mm four-layer placement, outward-facing connectors and four M3 mounting holes with screw-head copper clearances. - Revised AP63203 buck supply, bulk/local decoupling, ADC supply filter and test points. - Schematic organized into…

Main components on the Routing candidate1

Routing candidate1 bill of materials (BOM)

73 components, 50 distinct parts.

QtyPartRefs
1
ADS1115IDGS
U1
1
AP63203WU-7
U3
1
ESP32-S3-WROOM-1-N16R8
U4
1
CP2102N-A02-GQFN28
U5
2
AO3400A
Q1, Q2
1
SCT-013-000 ONLY
J1
1
REGULATED 5V INPUT
J2
1
THERMAL_I2C
J3
1
USB_C_Receptacle_USB2.0_14P
J4
1
TEST_LOAD
J5
1
Buzzer (3V3 type TBD)
BZ1
1
046701.5NRHF 1.5A
F1
1
G5LE-1 DC5
K1
1
BOOT
SW2
1
RESET
SW3
1
M7 (1N4007 SMD)
D1
1
ADC POWER
D2
1
POWER
D5
1
SMLVN6RGB1U1
D6
1
SP0503BAHTG
D7
Show 30 more
QtyPartRefs
1
USB BRIDGE POWER
D8
2
BAT54S
D9, D10
1
6.8uH SRP5030TA-6R8M
L1
1
220nF
C1
2
10uF
C2, C9
2
100nF
C3, C10
1
10uF 10V X7R
C4
1
10uF 10V X7R
C5
2
100nF 10V X7R
C6, C20
3
22uF 10V X7R
C7, C8, C23
1
1uF
C11
2
100nF
C15, C18
2
4.7uF
C16, C17
1
10uF 10V X7R
C19
1
100nF 25V X7R
C21
2
100uF 10V
C22, C24
2
1k 1%
R1, R2
2
10k 1%
R3, R4
2
100
R6, R15
2
4.7k
R7, R8
2
1k
R9, R21
5
330
R12, R16, R17, R18, R22
2
10k
R13, R14
1
22.1k
R19
1
47.5k
R20
1
18 ohm 1% 0.25W
R23
2
5.1k
R24, R25
3
100k
R26, R27, R28
1
0R 1A min
R29
1
10R 1%
R30

Routing candidate1 design files

The KiCad project lives in the c-lydia/SmartDB repository on GitHub; these links point at the commit this page was built from.

Routing candidate1: common questions

What microcontroller does the Routing candidate1 use?

The Routing candidate1 is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the Routing candidate1 PCB?

The Routing candidate1 measures 95 × 78 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Routing candidate1?

73 components, from 50 distinct parts. The full bill of materials is listed on this page.

Where can I download the Routing candidate1 design files?

From the c-lydia/SmartDB repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Routing candidate1 design in my own project?

Yes, under the terms of its Apache-2.0 license, which c-lydia chose for the repository.

Can I test firmware for the Routing candidate1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in SmartDB

Similar boards