Pax-DLED
CalinRadoni·pax-DLED·HW/dled-esp32-controller.kicad_pcb
About the Pax-DLED PCB
Pax-DLED is an open source ESP32 PCB design by CalinRadoni, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 50 × 48 mm, with 39 components from 26 distinct parts.
Its main chip is the ESP-WROOM-32, from the ESP32 family. Other key parts include the BD48K28...30, TLV62569DBV and SN74LV1T34. By type, the board carries 10 resistors, 9 connectors, 9 capacitors, 5 ICs, 2 transistors and 1 diode.
It belongs with the iot & wireless, displays & leds and power & battery designs in this gallery.
From the project
Efficiency, hardware control for digital LEDs and Wi-Fi communications - these are just some of the caracteristics of this controller.
Efficiency, hardware control for digital LEDs and Wi-Fi communications - these are just some of the caracteristics of this controller.
It is designed to control digital LEDS like:
- WS2812, WS2812B, ... (aka NeoPixel) and derivatives like SK6812 - APA102 (aka DotStar) and derivatives like SK9822
- using the ESP32's RMT peripheral, the controller is able to drive two strips of digital LEDs like: WS2812, WS2812B, WS2812C, WS2812S, WS2813, WS2815, WS2812D, etc. - using the ESP32's HSPI peripheral, the controller is able to drive a strip of digital LEDs like APA102 - two real logic level…

Main components on the Pax-DLED
Pax-DLED bill of materials (BOM)
39 components, 26 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP-WROOM-32 | ESP-WROOM-32-HandSolder | U1 |
| 1 | BD48K28...30 | SOT-23-HS | U2 |
| 1 | TLV62569DBV | SOT-23-5-HS | U3 |
| 2 | SN74LV1T34 | SOT-23-5-HS | U4, U5 |
| 1 | STD46P4LLF6 | TO-252 | Q1 |
| 1 | IRLML2502 | SOT-23-GSD-HS | Q2 |
| 1 | CS_4 | Pin_Header_Straight_1x04 | J1 |
| 1 | CS_3 | Pin_Header_Straight_1x03_Cyan | J2 |
| 2 | CS_2 | Pin_Header_Straight_1x02 | J3, J4 |
| 1 | CS_3 | Pin_Header_Straight_1x03_Yellow | J5 |
| 1 | CS_5 | Pin_Header_Straight_1x05 | J6 |
| 1 | CS_3 | Pin_Header_Straight_1x03 | J7 |
| 2 | CS_Pwr | DG301-5-2 | J8, J9 |
| 2 | Hole | HoleNPT-M3 | H1, H2 |
| 1 | LED | LED1206 | D1 |
| 1 | 2.2uH | ASPI-0530HI | L1 |
| 5 | 100nF | C0805HS | C1, C2, C5, C6, C9 |
| 1 | 10uF | C0805HS | C3 |
| 1 | 100nF-NC | C0805HS | C4 |
| 1 | 10uF/10V/1mOhm | C0805HS | C7 |
Show 6 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 22uF/6.3V/1mOhm | C0805HS | C8 |
| 2 | 10k | R0805HS | R1, R8 |
| 4 | 330 | R0805HS | R2, R5, R9, R10 |
| 2 | 2k2 | R0805HS | R3, R4 |
| 1 | 442k 1% | R0805HS | R6 |
| 1 | 100k 1% | R0805HS | R7 |
Pax-DLED design files
The KiCad project lives in the CalinRadoni/pax-DLED repository on GitHub; these links point at the commit this page was built from.
Pax-DLED: common questions
What microcontroller does the Pax-DLED use?
The Pax-DLED is built around the ESP-WROOM-32, from the ESP32 family.
How big is the Pax-DLED PCB?
The Pax-DLED measures 50 × 48 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Pax-DLED?
39 components, from 26 distinct parts. The full bill of materials is listed on this page.
Where can I download the Pax-DLED design files?
From the CalinRadoni/pax-DLED repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Pax-DLED design in my own project?
Yes, under the terms of its GPL-3.0 license, which CalinRadoni chose for the repository.
Can I test firmware for the Pax-DLED without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k