CellKeeper isoSPI Hat

cellkeeper-bms·cellkeeper-hardware·isoSPI-Hat/isoSPI-Hat.kicad_pcb

CellKeeper isoSPI Hat layout, top view — open source RP2040/RP2350 board by cellkeeper-bms

About the CellKeeper isoSPI Hat

CellKeeper isoSPI Hat is an open source RP2040/RP2350 PCB design by cellkeeper-bms, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 44 × 37.8 mm, with 19 components from 12 distinct parts.

Its main chip is the RaspberryPi_Pico, from the RP2040/RP2350 family. Other key parts include the SP3485EN-L/TR and AM26LV32EIDR. By type, the board carries 10 capacitors, 3 resistors, 2 ICs, 2 connectors and 1 module.

It belongs with the power & battery and dev boards & breakouts designs in this gallery.

From the project

PCB for the CellKeeper BMS

KiCad PCB design for the CellKeeper Battery Management System, a replacement BMS controller for battery packs using the isoSPI protocol. The main board fits the Tesla battery's penthouse: the pack's original harness, HV sense, shunt and BMB connectors plug into it, and it mounts on the original brackets.

Each ordered revision has a release with its Gerbers, JLCPCB BOM and CPL, schematic PDF, board PDF (3D views and 1:1 prints) and the enclosure print files. Rev 1.1 was ordered on 2026-10-28; work towards rev 1.2 is on the rev1.2 branch.

CellKeeper isoSPI Hat, from the project README
From the project README

Main components on the CellKeeper isoSPI Hat

CellKeeper isoSPI Hat bill of materials (BOM)

19 components, 12 distinct parts.

QtyPartRefs
1
SP3485EN-L/TR
U1
1
AM26LV32EIDR
U2
1
RaspberryPi_Pico
A1
1
OEM Connector
J1
1
3.81P Screw Terminal
J2
1
HM2113ZNLT
TR1
3
100nF
C1, C2, C10
2
1nF
C3, C4
4
1uF
C5, C6, C7, C8
1
100pF
C9
2
47r
R1, R2
1
100R
R3

CellKeeper isoSPI Hat design files

The KiCad project lives in the cellkeeper-bms/cellkeeper-hardware repository on GitHub; these links point at the commit this page was built from.

CellKeeper isoSPI Hat: common questions

What microcontroller does the CellKeeper isoSPI Hat use?

The CellKeeper isoSPI Hat is built around the RaspberryPi_Pico, from the RP2040/RP2350 family.

How big is the CellKeeper isoSPI Hat?

The CellKeeper isoSPI Hat measures 44 × 37.8 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the CellKeeper isoSPI Hat?

19 components, from 12 distinct parts. The full bill of materials is listed on this page.

Where can I download the CellKeeper isoSPI Hat design files?

From the cellkeeper-bms/cellkeeper-hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the CellKeeper isoSPI Hat design in my own project?

Yes, under the terms of its GPL-3.0 license, which cellkeeper-bms chose for the repository.

Can I test firmware for the CellKeeper isoSPI Hat without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in cellkeeper-hardware

Similar boards