CellKeeper

cellkeeper-bms·cellkeeper-hardware·CellKeeper/CellKeeper.kicad_pcb

CellKeeper PCB layout, top view — open source RP2040/RP2350 board by cellkeeper-bms

About the CellKeeper PCB

CellKeeper is an open source RP2040/RP2350 PCB design by cellkeeper-bms, published on GitHub under the GPL-3.0 license. It is a 4-layer board measuring 260 × 113 mm, with 405 components from 74 distinct parts.

Its main chip is the RP2354B, from the RP2040/RP2350 family. Other key parts include the UCC27524DR, TPS5430DDAR, F0505S-1WR3, ISO1050DUB and LTV-217-B-G. By type, the board carries 140 resistors, 106 capacitors, 50 diodes, 33 jumpers, 25 ICs and 21 connectors.

It belongs with the power & battery designs in this gallery.

From the project

PCB for the CellKeeper BMS

KiCad PCB design for the CellKeeper Battery Management System, a replacement BMS controller for battery packs using the isoSPI protocol. The main board fits the Tesla battery's penthouse: the pack's original harness, HV sense, shunt and BMB connectors plug into it, and it mounts on the original brackets.

Each ordered revision has a release with its Gerbers, JLCPCB BOM and CPL, schematic PDF, board PDF (3D views and 1:1 prints) and the enclosure print files. Rev 1.1 was ordered on 2026-10-28; work towards rev 1.2 is on the rev1.2 branch.

CellKeeper, from the project README
From the project README

Main components on the CellKeeper

CellKeeper bill of materials (BOM)

405 components, 74 distinct parts.

QtyPartRefs
2
UCC27524DR
U1, U11
1
TPS5430DDAR
U3
2
F0505S-1WR3
U4, U15
2
ISO1050DUB
U5, U10
6
LTV-217-B-G
U6, U7, U8, U9, U12, U13
2
RP2354B
U14, U20
1
ISO1540
U16
1
INA228
U17
2
ADS1115
U18, U19
1
SP3485EN-L/TR
U21
1
AM26LV32EIDR
U22
2
W25Q16JVUXIQ
U23, U24
2
TLV1117LV33DCYR
U25, U26
4
BSC0805LS
Q1, Q2, Q3, Q4
2
ABM8-272-T3
Y1, Y2
2
WJ15EDGRC-3.81-04P-14-00A
J1, J15
1
T34008
J2
2
Screw_Terminal_01x04
J3, J7
2
8P8C_LED_Shielded_x2
J4, J5
1
S44B-RAD1AK
J6
Show 54 more
QtyPartRefs
2
Conn_01x03
J8, J16
3
USB_C_Receptacle_USB2.0_16P
J9, J11, J19
1
3.81P Screw Terminal
J10
2
Conn_02x10_Odd_Even
J12, J22
1
ZE05H-8DP-2H
J14
1
OEM HV Sense Connector
J17
1
7.62mm Pitch Screw Terminal
J18
1
OEM Connector
J20
1
3.81P Screw Terminal
J21
7
TP
1/2V1, 3v1, 5V1, GND1, GPIO44, GPIO45, GPIO46
2
SDCW3225S-2-102TF
FL1, FL2
33
0r
JP3, JP4, JP5, JP6, JP7, JP8, JP9, JP10 +25
4
TS-1187A-B-A-B
SW1, SW2, SW3, SW4
1
HM2113ZNLT
TR1
13
SMB6.8CA
D1, D2, D3, D4, D5, D6, D24, D25 +5
9
Green
D7, D8, D14, D19, D32, D35, D36, D43 +1
6
Red
D9, D10, D27, D41, D46, D49
12
SS54
D11, D12, D15, D16, D20, D23, D37, D38 +4
6
White
D13, D17, D22, D33, D34, D45
4
SMCJ33CA
D18, D21, D39, D40
3
600R@100MHz
FB1, FB3, FB5
1
120Ω@100MHz
FB2
2
6.8uh
L1, L5
2
22uh 5.5A
L2, L3
2
3.3uh
L4, L6
3
680uF
C1, C14, C31
30
100nF
C2, C10, C11, C13, C15, C16, C18, C22 +22
10
10uF
C3, C4, C6, C8, C17, C21, C32, C55 +2
8
22uF
C5, C7, C12, C33, C37, C48, C49, C69
1
4.7uF
C9
9
1uF
C19, C20, C41, C42, C67, C96, C97, C98 +1
5
100pF
C24, C25, C26, C27, C103
8
4.7u
C38, C43, C45, C52, C68, C72, C82, C87
4
15pF
C39, C40, C70, C71
26
100n
C44, C46, C47, C50, C51, C53, C56, C57 +18
2
1nF
C94, C95
17
24k
R1, R2, R11, R16, R29, R33, R35, R39 +9
17
10k
R3, R4, R13, R14, R15, R17, R19, R20 +9
8
100k
R5, R10, R18, R24, R34, R36, R151, R152
4
33R
R7, R12, R37, R38
12
1k
R8, R9, R22, R23, R46, R47, R48, R49 +4
3
3.3k
R26, R78, R155
13
1k
R27, R53, R55, R56, R74, R92, R94, R95 +5
3
510r
R30, R73, R86
2
120r
R31, R32
2
2.2k
R43, R44
20
5.1k
R45, R57, R66, R69, R72, R77, R79, R80 +12
4
33r
R54, R68, R93, R126
4
22R
R70, R71, R127, R128
2
220r
R87, R88
24
3M
R102, R103, R104, R105, R106, R107, R108, R109 +16
2
47r
R136, R137
1
100R
R142
2
1M
R145, R146

CellKeeper design files

The KiCad project lives in the cellkeeper-bms/cellkeeper-hardware repository on GitHub; these links point at the commit this page was built from.

CellKeeper: common questions

What microcontroller does the CellKeeper use?

The CellKeeper is built around the RP2354B, from the RP2040/RP2350 family.

How big is the CellKeeper PCB?

The CellKeeper measures 260 × 113 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the CellKeeper?

405 components, from 74 distinct parts. The full bill of materials is listed on this page.

Where can I download the CellKeeper design files?

From the cellkeeper-bms/cellkeeper-hardware repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.

Can I use the CellKeeper design in my own project?

Yes, under the terms of its GPL-3.0 license, which cellkeeper-bms chose for the repository.

Can I test firmware for the CellKeeper without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

More boards in cellkeeper-hardware

Similar boards