50 open source boards using the SP3485EN-L/TR
Real designs built with the SP3485EN-L/TR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
AnthC
Anthilla
85 × 56 mm203 parts4LNo license40HPM5E31 ECatDualFOC
LX050724
85 × 113 mm559 parts4LMIT14RP2040/RP2350
CellKeeper
cellkeeper-bms
260 × 113 mm405 parts4LGPL-3.011RP2040/RP2350
HALPI2-hardware
hatlabs
187 × 109 mm541 parts6LCustom license9ESP32
Open Shot Clock Display
DLaxV-Community-Projects-Hub
100 × 75 mm196 parts2LCERN-OHL-P-2.05ESP32
Dreimaskin-ELS
jonasnic
95.6 × 86.1 mm71 parts4LNo license1Robothardware
des256
190 × 130 mm364 parts4LNo license0ESP32
Ptz driver
Aottens
100 × 80 mm251 parts4LNo license0STM32
Default
RileyLeff
100 × 65 mm234 parts6LNo license0Kicadtest
swissbyte
100 × 160 mm134 parts2LNo license0ESP32
De.freezweb.heizungssteuerung
freezweb
160 × 110 mm114 parts2LNo license0Raspberry Pi
1.2
tomrodinger
46.2 × 30.9 mm86 parts2LApache-2.00ESP32
Before backlabels
mitra42
64 × 37 mm63 parts2LNo license0ESP32
PCB SALUS V3
LeoSole423
100 × 100 mm63 parts2LNo license0ESP32
Before backlabels
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Dmxnow
feraudet
146 × 65.5 mm56 parts2LCustom license0ESP32
Pl60c dmx
tsmiltonAgents
80 × 54 mm36 parts2LNo license0RP2040/RP2350
CellKeeper isoSPI Hat
cellkeeper-bms
44 × 37.8 mm19 parts4LGPL-3.011ESP32
Open Shot Clock Controller
DLaxV-Community-Projects-Hub
100 × 47.5 mm164 parts2LCERN-OHL-P-2.05STM32
LB-100
avlyubimov
100 × 70 mm99 parts6LCustom license1ESP32
Rev a input
Aottens
100 × 80 mm251 parts4LNo license0STM32
Default.active pre v0.2-hydration
RileyLeff
100 × 65 mm234 parts6LNo license0Raspberry Pi
V9
tomrodinger
46.7 × 30.9 mm76 parts2LApache-2.00ESP32
Before import
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Before import
mitra42
64 × 37 mm63 parts2LNo license0STM32
Default.shipped v0.1
RileyLeff
100 × 65 mm234 parts6LNo license0RP2040/RP2350
BDCMotorControlBoard
nunosousa
110 × 37 mm87 parts4LMIT0Raspberry Pi
1.1
tomrodinger
46.2 × 30.9 mm75 parts2LApache-2.00ESP32
Before islands
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Before islands
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Before join
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Before join
mitra42
64 × 37 mm63 parts2LNo license0Raspberry Pi
Uw rs485 hat-V5
tomrodinger
46.7 × 30.9 mm53 parts2LApache-2.00ESP32
Before polarity
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Before polarity
mitra42
64 × 37 mm63 parts2LNo license0ESP32
Before pour
mitra42
64 × 37 mm63 parts2LNo license0
How designs wire the SP3485EN-L/TR
Read from the KiCad layouts of 18 open source designs, one per repository: what each pin of the SP3485EN-L/TR connects to, and the resistors, capacitors and other passives placed on it.
- The A pin has a series resistor on 15 of 18 designs, most often 120 Ω (then 47 Ω).
- The VCC pin has a decoupling capacitor on 13 of 18 designs, most often 100 nF (then 1 µF).
- The B pin has a series resistor on 10 of 18 designs, most often 120 Ω (then 47 Ω).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| REpin 2 | Connected to: The microcontroller 44% |
|
| DEpin 3 | Connected to: The microcontroller 44% |
|
| GNDpin 5 | Connected to: GND 100% | — |
| Apin 6 | Connected to: A connector 61% |
|
| Bpin 7 | Connected to: A connector 61% |
|
| VCCpin 8 | Connected to: 3.3V 83% · a signal 17% |
|
2 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include AnthC by Anthilla, HPM5E31 ECatDualFOC by LX050724, CellKeeper by cellkeeper-bms and HALPI2-hardware by hatlabs.
The SP3485EN-L/TR in open source designs
The gallery holds 50 open source boards using the SP3485EN-L/TR from 19 GitHub repositories; a typical one measures about 64 × 37 mm and carries around 63 components.
70% are two-layer designs, the rest use four layers or more, and 20% carry an open source license.
The most starred is AnthC by Anthilla.
Parts used alongside the SP3485EN-L/TR
Microcontrollers on boards using the SP3485EN-L/TR
What boards using the SP3485EN-L/TR are built for
SP3485EN-L/TR: common questions
Where can I find a SP3485EN-L/TR reference design?
Each of the 50 boards on this page is a real design using the SP3485EN-L/TR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the SP3485EN-L/TR A pin?
The A pin has a series resistor on 15 of 18 designs, most often 120 Ω (then 47 Ω). Counted from the KiCad layouts of 18 open source designs using the SP3485EN-L/TR.
What decoupling capacitors do designs use on the SP3485EN-L/TR VCC pin?
The VCC pin has a decoupling capacitor on 13 of 18 designs, most often 100 nF (then 1 µF). Counted from the KiCad layouts of 18 open source designs using the SP3485EN-L/TR.
What resistor goes on the SP3485EN-L/TR B pin?
The B pin has a series resistor on 10 of 18 designs, most often 120 Ω (then 47 Ω). Counted from the KiCad layouts of 18 open source designs using the SP3485EN-L/TR.
What parts are used alongside the SP3485EN-L/TR?
The AMS1117-3.3, AP2112K-3.3TRG1, ESP32-C3-WROOM-02U-N4, INA180A1 and ME6211C33M5G-N appear in the most repositories here.
Which microcontrollers do boards using the SP3485EN-L/TR use?
Most are built on ESP32 (35), Raspberry Pi (4), RP2040/RP2350 (4) and STM32 (4).
How big is a typical board using the SP3485EN-L/TR?
The median is 64 × 37 mm, and 70% are two-layer designs.
What is the most popular open source board using the SP3485EN-L/TR?
By GitHub stars, AnthC by Anthilla, with 40 stars.
Can I simulate one of these boards using the SP3485EN-L/TR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.