DomoDisp
About the DomoDisp PCB
DomoDisp is an open source ESP8266 PCB design by chipsi007, published on GitHub under the MIT license. It is a 2-layer board measuring 100 × 85 mm, with 20 components from 10 distinct parts.
Its main chip is the ESP-12, from the ESP8266 family. Other key parts include the AP111733. By type, the board carries 12 resistors, 2 ICs, 2 connectors, 2 capacitors and 1 switch.
It belongs with the displays & leds designs in this gallery.
From the project
This project consists of a protocol spec, the design files for physical nodes and the source code that glues it together.
This project consists of a protocol spec, the design files for physical nodes and the source code that glues it together.
Full protocol description is available, together with examples of a monitor and a sender. The protocol is text-based to ease debugging.
ClearSky technology inside: the basic concept is that no coordinator is needed for the nodes to work after the initial configuration. There must not be a single point of (catastrophic) failure. And obviously no "cloud" (hence ClearSky) service is needed either: you, and only you, decide if/when/which data can exit from your network!
Main components on the DomoDisp
DomoDisp bill of materials (BOM)
20 components, 10 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | AP111733 | SOT-223 | U1 |
| 1 | ESP-12 | ESP-12 | U2 |
| 1 | CONN_02X05 | Multicomp_MC9A12-1034_2x05x2.54mm_Straight | P1 |
| 1 | CONN_01X03 | Pin_Header_Straight_1x03_Pitch2.54mm | P2 |
| 1 | ST7735 | ST7735_module | ST7735_MODULE1 |
| 1 | Rotary_Encoder_Switch | rotary-encoder | SW1 |
| 2 | C | C_0805 | C1, C2 |
| 5 | 10k | R_0805 | R1, R2, R3, R11, R12 |
| 6 | 10k 1% | R_0805 | R4, R5, R6, R8, R9, R10 |
| 1 | 10R 1/4W | R_Axial_DIN0309_L9.0mm_D3.2mm_P12.70mm_Horizontal | R7 |
DomoDisp design files
The KiCad project lives in the chipsi007/HomeAutomation repository on GitHub; these links point at the commit this page was built from.
DomoDisp: common questions
What microcontroller does the DomoDisp use?
The DomoDisp is built around the ESP-12, from the ESP8266 family.
How big is the DomoDisp PCB?
The DomoDisp measures 100 × 85 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the DomoDisp?
20 components, from 10 distinct parts. The full bill of materials is listed on this page.
Where can I download the DomoDisp design files?
From the chipsi007/HomeAutomation repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the DomoDisp design in my own project?
Yes, under the terms of its MIT license, which chipsi007 chose for the repository.
Can I test firmware for the DomoDisp without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP8266 firmware against it before you order a PCB.
More boards in HomeAutomation
Similar boards
ESP8266ESP8266ControllerCircuit
stuartpittaway
75 × 30 mm20 parts2LCC-BY-NC-4.01.1k
ESP8266HASwitchPlate
aderusha
60 × 40 mm8 parts2LMIT738
ESP8266Goatgdo
Kaldek
32.9 × 53.3 mm23 parts2LMIT506
ESP8266RatGDO-OpenSource-Bare-ESP8266
55 × 82.7 mm20 parts2LMIT506
ESP8266RatGDO-OpenSource-D1Mini-ESP8266
47.8 × 63.3 mm12 parts2LMIT506
ESP8266Iaq board
nkitanov
70.1 × 43.2 mm17 parts2LNo license398