Rove sv
crzhacko·rove-esp32s3·electronics/rove_sv/rove_sv.kicad_pcb
About the Rove sv PCB
Rove sv is an open source ESP32 PCB design by crzhacko, published on GitHub. It is a 2-layer board measuring 60 × 50 mm, with 27 components from 24 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the DRV8833PW, XC6220B331MR and DW01A. By type, the board carries 7 resistors, 6 connectors, 6 capacitors, 4 ICs, 1 transistor and 1 microphone.
It belongs with the robotics & motion and power & battery designs in this gallery.
From the project
ROVE — ESP32-S3 voice-controlled RC car platform (monorepo: firmware + electronics)
Offline voice-controlled toy car platform based on the ESP32-S3-WROOM-1. No internet required — all speech recognition runs on-device via ESP-SR.
See docs/rovevariants.md` for full pin assignment, build instructions, and BOM.
Wake word: "Hey ESP" — then say "go forward", "turn left", "stop", etc.
- MCU: ESP32-S3-WROOM-1 (16 MB flash, 8 MB PSRAM) - Motor driver: DRV8833PW dual H-bridge - Charger: TP4056 via USB-C (580 mA) - LDO: XC6220B331MR (3.3 V) - Microphone: INMP441 I2S MEMS - Board: 60 × 50 mm (smaller than Arduino Uno)
Main components on the Rove sv
Rove sv bill of materials (BOM)
27 components, 24 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 1 | DRV8833PW | TSSOP-16_4.4x5mm_P0.65mm | U2 |
| 1 | XC6220B331MR | SOT-23-5 | U3 |
| 1 | DW01A | SOT-23-6 | U5 |
| 1 | FS8205A | SOT-23-6 | Q1 |
| 1 | USB-C | USB_C_Receptacle_HRO_TYPE-C-31-M-12 | J1 |
| 1 | Battery | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J2 |
| 1 | LeftMotor | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J3 |
| 1 | RightMotor | JST_PH_B2B-PH-K_1x02_P2.00mm_Vertical | J4 |
| 1 | Servo1 | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | Servo2 | PinHeader_1x03_P2.54mm_Vertical | J6 |
| 1 | INMP441 | INMP441_LGA-6 | MK1 |
| 1 | BOOT | SW_SPST_SKQG_WithoutStem | SW1 |
| 1 | Blue | LED_0805_2012Metric | D1 |
| 1 | 10uF | CP_Elec_6.3x5.8 | C1 |
| 2 | 0.1uF | C_0805_2012Metric | C2, C7 |
| 1 | 100uF | CP_Elec_6.3x5.8 | C5 |
| 1 | 10nF | C_0805_2012Metric | C6 |
| 1 | 100nF | C_0805_2012Metric | C8 |
| 2 | 10k | R_0805_2012Metric | R1, R2 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 330R | R_0805_2012Metric | R3 |
| 2 | 5.1k | R_0805_2012Metric | R4, R5 |
| 1 | 100k | R_0402_1005Metric | R6 |
| 1 | 47k | R_0402_1005Metric | R7 |
Rove sv design files
The KiCad project lives in the crzhacko/rove-esp32s3 repository on GitHub; these links point at the commit this page was built from.
Rove sv: common questions
What microcontroller does the Rove sv use?
The Rove sv is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How big is the Rove sv PCB?
The Rove sv measures 60 × 50 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Rove sv?
27 components, from 24 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Rove sv design files?
From the crzhacko/rove-esp32s3 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Rove sv design in my own project?
The repository has no license, so all rights stay with crzhacko. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Rove sv without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in rove-esp32s3
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k