Rove v

crzhacko·rove-esp32s3·electronics/rove_v/rove_v.kicad_pcb

Rove v PCB layout, top view — open source ESP32 board by crzhacko

About the Rove v PCB

Rove v is an open source ESP32 PCB design by crzhacko, published on GitHub. It is a 2-layer board measuring 60 × 50 mm, with 25 components from 22 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the DRV8833PW, XC6220B331MR and DW01A. By type, the board carries 7 resistors, 6 capacitors, 4 ICs, 4 connectors, 1 transistor and 1 microphone.

It belongs with the robotics & motion and power & battery designs in this gallery.

From the project

ROVE — ESP32-S3 voice-controlled RC car platform (monorepo: firmware + electronics)

Offline voice-controlled toy car platform based on the ESP32-S3-WROOM-1. No internet required — all speech recognition runs on-device via ESP-SR.

See docs/rovevariants.md` for full pin assignment, build instructions, and BOM.

Wake word: "Hey ESP" — then say "go forward", "turn left", "stop", etc.

- MCU: ESP32-S3-WROOM-1 (16 MB flash, 8 MB PSRAM) - Motor driver: DRV8833PW dual H-bridge - Charger: TP4056 via USB-C (580 mA) - LDO: XC6220B331MR (3.3 V) - Microphone: INMP441 I2S MEMS - Board: 60 × 50 mm (smaller than Arduino Uno)

Main components on the Rove v

Rove v bill of materials (BOM)

25 components, 22 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
DRV8833PW
U2
1
XC6220B331MR
U3
1
DW01A
U5
1
FS8205A
Q1
1
USB-C
J1
1
Battery
J2
1
LeftMotor
J3
1
RightMotor
J4
1
INMP441
MK1
1
BOOT
SW1
1
Blue
D1
1
10uF
C1
2
0.1uF
C2, C7
1
100uF
C5
1
10nF
C6
1
100nF
C8
2
10k
R1, R2
1
330R
R3
2
5.1k
R4, R5
Show 2 more
QtyPartRefs
1
100k
R6
1
47k
R7

Rove v design files

The KiCad project lives in the crzhacko/rove-esp32s3 repository on GitHub; these links point at the commit this page was built from.

Rove v: common questions

What microcontroller does the Rove v use?

The Rove v is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Rove v PCB?

The Rove v measures 60 × 50 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rove v?

25 components, from 22 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Rove v design files?

From the crzhacko/rove-esp32s3 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Rove v design in my own project?

The repository has no license, so all rights stay with crzhacko. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Rove v without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in rove-esp32s3

Similar boards