16 open source boards using the DRV8833PW
Real designs built with the DRV8833PW, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Penguin bot
jeevan9s
89.5 × 62.6 mm141 parts4LNo license0ESP32
Haptic-Glove
ZharbolatDinmukhamed
62 × 46.9 mm108 parts4LNo license0Micromouse-Project
M595-DOT
79.5 × 56.5 mm58 parts2LNo license0NXP
Roboracing micromouse
RoboJackets
97.5 × 75 mm57 parts4LNo license0ESP32
Custom Esp32 Devboard
shreyD2408
84 × 72 mm55 parts4LNo license0EEE3088F-Power-Subsystem
Athenkosi-Khonzani
79 × 58 mm53 parts2LNo license0EEE3088F Power Subsystem Group61
Sipho-Junior
83 × 68.5 mm48 parts2LNo license0ESP32
Unflying-Fish
DinosaurPotato534
114.9 × 89.5 mm41 parts2LNo license0ESP32
Rove sv
crzhacko
60 × 50 mm27 parts2LNo license0AVR/Arduino
Receiver
devansh2004sharma-tech
66.5 × 39 mm21 parts2LNo license0AVR/Arduino
Cat-Gate-Controller v1.0
bgmbzk
68 × 44.6 mm18 parts2LNo license0- schematic only · 17 parts
Design-Project
wizzy713
17 partsNo license0 STM32
Robot pcb0
svenssonjoel
61.9 × 57.8 mm77 parts2LGPL-3.01ESP32
Rove v
crzhacko
60 × 50 mm25 parts2LNo license0ESP32
Kicad
jacksterb1234
74.3 × 54.6 mm17 parts2LNo license0RP2040/RP2350
Half line fpc
neilpstevenson
31.1 × 40.2 mm24 parts2LMIT0
How designs wire the DRV8833PW
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the DRV8833PW connects to, and the resistors, capacitors and other passives placed on it.
- The VINT pin has a capacitor to GND on 13 of 14 designs, most often 2.2 µF (then 100 nF).
- The AISEN pin is tied to GND on 10 of 14 designs (a signal on 4).
- The BISEN pin is tied to GND on 10 of 14 designs (a signal on 4).
- The FAULT pin is left unconnected on 9 of 14 designs (a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| AISENpin 3 | Connected to: GND 71% · a signal 29% | — |
| BISENpin 6 | Connected to: GND 71% · a signal 29% | — |
| FAULTpin 8 | Connected to: Not connected 64% · a signal 29% | — |
| VCPpin 11 | Connected to: Signal 86% |
|
| VMpin 12 | Connected to: VBAT 64% · a signal 36% |
|
| GNDpin 13 | Connected to: GND 94% | — |
| VINTpin 14 | Connected to: Signal 71% · VCC 21% |
|
9 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Robot pcb0 by svenssonjoel, EEE3088F-Power-Subsystem by Athenkosi-Khonzani, Cat-Gate-Controller v1.0 by bgmbzk and Rove sv by crzhacko.
The DRV8833PW in open source designs
The gallery holds 16 open source boards using the DRV8833PW from 15 GitHub repositories; a typical one measures about 74.3 × 56.5 mm and carries around 45 components.
73% are two-layer designs, the rest use four layers or more, and 13% carry an open source license.
The most starred is Robot pcb0 by svenssonjoel.
Parts used alongside the DRV8833PW
Microcontrollers on boards using the DRV8833PW
What boards using the DRV8833PW are built for
DRV8833PW: common questions
Where can I find a DRV8833PW reference design?
Each of the 16 boards on this page is a real design using the DRV8833PW. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the DRV8833PW VINT pin connected?
The VINT pin has a capacitor to GND on 13 of 14 designs, most often 2.2 µF (then 100 nF). Counted from the KiCad layouts of 14 open source designs using the DRV8833PW.
How is the DRV8833PW AISEN pin connected?
The AISEN pin is tied to GND on 10 of 14 designs (a signal on 4). Counted from the KiCad layouts of 14 open source designs using the DRV8833PW.
How is the DRV8833PW BISEN pin connected?
The BISEN pin is tied to GND on 10 of 14 designs (a signal on 4). Counted from the KiCad layouts of 14 open source designs using the DRV8833PW.
What parts are used alongside the DRV8833PW?
The CH224K, INA219AxD, AMS1117-3.3, MT3608 and TP4056 appear in the most repositories here.
Which microcontrollers do boards using the DRV8833PW use?
Most are built on ESP32 (7), AVR/Arduino (2), NXP (1) and RP2040/RP2350 (1).
How big is a typical board using the DRV8833PW?
The median is 74.3 × 56.5 mm, and 73% are two-layer designs.
What is the most popular open source board using the DRV8833PW?
By GitHub stars, Robot pcb0 by svenssonjoel, with 1 stars.
Can I simulate one of these boards using the DRV8833PW before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.