HardLabs

10x10

DAlexis·caustic-lasertag-system·schematic/grouped-boards/head-rifle-rev3/10x10.kicad_pcb

10x10 PCB layout, top view — open source board by DAlexis
Simulate this board

About the 10x10 PCB

10x10 is an open source PCB design by DAlexis, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 92.5 × 96 mm, with 60 components from 39 distinct parts.

Other key parts include the PAM8403, RGB-LED, TSOP4856 and MCP73831. By type, the board carries 17 resistors, 13 connectors, 11 capacitors, 7 transistors, 4 ICs and 2 relays.

It belongs with the iot & wireless designs in this gallery.

From the project

Caustic project is a full-featured indoor and outdoor lasertag system

Caustic Lasertag System licensed under GPLv3. Third party code used in project may be licensed under other licences, see corresponding files and comments in the sources. Copyright 2016, see AUTHORS file.

You need to install cmake, arm-none-eabi-gcc compiler with arm-none-eabi-newlib and arm-none-eabi-binutils installed, and installation dirs should be in $PATH. Simply installation from your distro's repository usually enough. To flash the MCU with ST-link programmer you should install stlink utility. Then:

Main components on the 10x10

PAM8403RGB-LEDTSOP4856MCP73831

10x10 bill of materials (BOM)

60 components, 39 distinct parts.

QtyPartRefs
1
PAM8403
U1
1
RGB-LED
U2
1
TSOP4856
U3
1
MCP73831
U4
1
MOSFET_P
Q1
6
MOS_N
Q2, Q3, Q4, Q5, Q6, Q7
1
8MHz
X2
1
SENSOR_CONNECTOR
P1
1
VibroEngine
P2
1
Mag&fireMode
P3
1
VCC
P4
1
Speaker2
P5
1
UART1
P6
1
Fire&Reload
P7
1
EXTENSION-CONNECTOR
P8
1
Zone1
P9
1
MCU2
P10
1
NRF24L01
P12
1
IR_LED
P13
1
Vibro&flash
P15
Show 19 more
QtyPartRefs
1
P***
1PIN
1
BATTERY
BT1
2
CONN_3
K1, K2
1
LED
D1
2
FILTER
FB1, FB2
1
4.7uF
C1
1
0.47uF
C2
1
0.015uF
C3
2
0.1uF
C4, C6
1
C
C5
2
CP1
C7, C10
1
470uF
C8
2
1uF
C9, C11
8
10k
R1, R3, R12, R13, R14, R15, R16, R17
1
470
R2
4
R
R4, R5, R6, R7
2
R
R8, R9
1
1.5k
R10
1
2k
R11

10x10 design files

The KiCad project lives in the DAlexis/caustic-lasertag-system repository on GitHub; these links point at the commit this page was built from.

10x10: common questions

How big is the 10x10 PCB?

The 10x10 measures 92.5 × 96 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the 10x10?

60 components, from 39 distinct parts. The full bill of materials is listed on this page.

Where can I download the 10x10 design files?

From the DAlexis/caustic-lasertag-system repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the 10x10 design in my own project?

Yes, under the terms of its GPL-3.0 license, which DAlexis chose for the repository.

More boards in caustic-lasertag-system

Similar boards