HardLabs

Hs mono g431-panelized

DAlexis·caustic-lasertag-system·schematic/head-sensor/monolith-G431/hs-mono-g431-panelized.kicad_pcb

Hs mono g431-panelized PCB layout, top view — open source STM32 board by DAlexis
Simulate this board

About the Hs mono g431-panelized PCB

Hs mono g431-panelized is an open source STM32 PCB design by DAlexis, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 78.1 × 85.7 mm, with 51 components from 30 distinct parts.

Its main chip is the STM32F103RE, from the STM32 family. Other key parts include the USBLC6-4, MCP73831, NCP551 and HC-05. By type, the board carries 15 capacitors, 13 resistors, 7 connectors, 5 ICs, 5 transistors and 4 diodes.

It belongs with the iot & wireless designs in this gallery.

From the project

Caustic project is a full-featured indoor and outdoor lasertag system

Caustic Lasertag System licensed under GPLv3. Third party code used in project may be licensed under other licences, see corresponding files and comments in the sources. Copyright 2016, see AUTHORS file.

You need to install cmake, arm-none-eabi-gcc compiler with arm-none-eabi-newlib and arm-none-eabi-binutils installed, and installation dirs should be in $PATH. Simply installation from your distro's repository usually enough. To flash the MCU with ST-link programmer you should install stlink utility. Then:

Main components on the Hs mono g431-panelized

STM32F103REUSBLC6-4MCP73831NCP551HC-05

Hs mono g431-panelized bill of materials (BOM)

51 components, 30 distinct parts.

QtyPartRefs
1
STM32F103RE
U1
1
USBLC6-4
U2
1
MCP73831
U3
1
NCP551
U4
1
HC-05
U5
1
IRLML6402
Q1
4
IRLML2502
Q2, Q3, Q4, Q5
1
8MHz
Y1
1
32768Hz
Y2
1
MICROSD-SDIO-CD
P1
1
SWD
P2
1
G B Vcc
P3
1
NRF24L01
P4
1
USB_A
P5
1
SENSOR_CONNECTOR
P6
1
DEBUG_TX
P7
1
Chrg
D1
1
DBG
D2
1
Link
D3
1
Mode
D4
Show 10 more
QtyPartRefs
3
100uF
C1, C12, C13
5
0.1
C2, C3, C4, C5, C9
4
20pF
C6, C7, C8, C15
2
0.1uF
C10, C11
1
4.7uF
C14
5
47k
R1, R2, R3, R4, R5
2
10k
R6, R7
1
1.5k
R8
4
470
R9, R11, R12, R13
1
2k
R10

Hs mono g431-panelized design files

The KiCad project lives in the DAlexis/caustic-lasertag-system repository on GitHub; these links point at the commit this page was built from.

Hs mono g431-panelized: common questions

What microcontroller does the Hs mono g431-panelized use?

The Hs mono g431-panelized is built around the STM32F103RE, from the STM32 family.

How big is the Hs mono g431-panelized PCB?

The Hs mono g431-panelized measures 78.1 × 85.7 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Hs mono g431-panelized?

51 components, from 30 distinct parts. The full bill of materials is listed on this page.

Where can I download the Hs mono g431-panelized design files?

From the DAlexis/caustic-lasertag-system repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Hs mono g431-panelized design in my own project?

Yes, under the terms of its GPL-3.0 license, which DAlexis chose for the repository.

Can I test firmware for the Hs mono g431-panelized without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in caustic-lasertag-system

Similar boards