HardLabs

Rifle mono v1-panelized

DAlexis·caustic-lasertag-system·schematic/rifle/monolith-v1/rifle-mono-v1-panelized.kicad_pcb

Rifle mono v1-panelized PCB layout, top view — open source STM32 board by DAlexis
Simulate this board

About the Rifle mono v1-panelized PCB

Rifle mono v1-panelized is an open source STM32 PCB design by DAlexis, published on GitHub under the GPL-3.0 license. It is a 2-layer board measuring 77.5 × 97.1 mm, with 75 components from 45 distinct parts.

Its main chip is the STM32F103RE, from the STM32 family. Other key parts include the USBLC6, MCP73831, NCP551 and PAM8403. By type, the board carries 24 resistors, 19 connectors, 17 capacitors, 7 transistors, 5 ICs and 2 diodes.

It belongs with the iot & wireless designs in this gallery.

From the project

Caustic project is a full-featured indoor and outdoor lasertag system

Caustic Lasertag System licensed under GPLv3. Third party code used in project may be licensed under other licences, see corresponding files and comments in the sources. Copyright 2016, see AUTHORS file.

You need to install cmake, arm-none-eabi-gcc compiler with arm-none-eabi-newlib and arm-none-eabi-binutils installed, and installation dirs should be in $PATH. Simply installation from your distro's repository usually enough. To flash the MCU with ST-link programmer you should install stlink utility. Then:

Main components on the Rifle mono v1-panelized

STM32F103REUSBLC6MCP73831NCP551PAM8403

Rifle mono v1-panelized bill of materials (BOM)

75 components, 45 distinct parts.

QtyPartRefs
1
STM32F103RE
U1
1
USBLC6
U2
1
MCP73831
U3
1
NCP551
U4
1
PAM8403
U5
1
IRLML6402
Q1
6
IRLML2502
Q2, Q3, Q4, Q5, Q6, Q7
1
8MHz
Y1
1
MICROSD-SDIO-CD
P1
1
SWD
P2
1
G B Vcc
P3
1
NRF24L01
P4
1
USB_A
P5
1
S_A_M1_M2
P6
1
DEBUG_TX
P7
1
Fire
P8
1
Reload
P9
1
RC522
P10
1
Speaker1
P11
1
Speaker2
P12
Show 25 more
QtyPartRefs
2
I2C display
P13, P14
1
FLASH
P15
1
VIBRO
P16
1
IR_LED
P17
1
USB_OTG
P18
1
GND
P19
1
Chrg
D1
1
DBG
D2
4
100uF
C1, C12, C13, C16
6
0.1
C2, C3, C4, C5, C9, C17
2
20pF
C6, C7
2
0.1uF
C10, C11
1
4.7uF
C14
1
0.015uF
C18
1
0.47uF
C19
5
47k
R1, R2, R3, R4, R5
10
10k
R6, R7, R13, R14, R15, R17, R19, R20 +2
1
1.5k
R8
2
470
R9, R11
1
2k
R10
1
100
R12
1
lev1
R16
1
lev2
R18
1
lev3
R21
1
lev4
R24

Rifle mono v1-panelized design files

The KiCad project lives in the DAlexis/caustic-lasertag-system repository on GitHub; these links point at the commit this page was built from.

Rifle mono v1-panelized: common questions

What microcontroller does the Rifle mono v1-panelized use?

The Rifle mono v1-panelized is built around the STM32F103RE, from the STM32 family.

How big is the Rifle mono v1-panelized PCB?

The Rifle mono v1-panelized measures 77.5 × 97.1 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Rifle mono v1-panelized?

75 components, from 45 distinct parts. The full bill of materials is listed on this page.

Where can I download the Rifle mono v1-panelized design files?

From the DAlexis/caustic-lasertag-system repository on GitHub, which has the KiCad layout; the links under Design files point to each one.

Can I use the Rifle mono v1-panelized design in my own project?

Yes, under the terms of its GPL-3.0 license, which DAlexis chose for the repository.

Can I test firmware for the Rifle mono v1-panelized without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in caustic-lasertag-system

Similar boards