DotGlow-ESP32

ElectroIoT·DotGlow-ESP32·hardware/pcb/kicad/dotglow-v1.kicad_pcb

DotGlow-ESP32 PCB layout, top view — open source ESP32 board by ElectroIoT

About the DotGlow-ESP32 PCB

DotGlow-ESP32 is an open source ESP32 PCB design by ElectroIoT, published on GitHub under the MIT license. It is a 2-layer board measuring 128 × 33 mm, with 35 components from 32 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N16R8, from the ESP32 family. Other key parts include the XL-B1515RGBA-HF, 74AHCT125, MAX98357A and USBLC6-2SC6. By type, the board carries 10 resistors, 8 capacitors, 7 connectors, 5 ICs, 3 switches and 1 diode.

It belongs with the iot & wireless, displays & leds and audio designs in this gallery.

From the project

DotGlow: WiFi + Bluetooth LED matrix clock firmware for ESP32 / ESP32-S3 + MAX7219, with Android app setup

A two-layer carrier that stacks on the back of a common MAX7219 4-in-1 (FC-16, 8 x 32) LED matrix module (128 x 31.1 x 15 mm measured, M3 holes). It replaces the dev board and the jumper wires.

The board that goes to the factory was finished in EasyEDA Pro (project "DotGlow V1 Board"): schematic ERC 0 errors, PCB DRC 0 errors, fully routed with net classes (5 V power 1.0 mm, 3.3 V and speaker 0.6 mm, display lines 0.25 mm), GND pour on both layers, antenna keep-out at the module end.

DotGlow-ESP32, from the project README
From the project README

Main components on the DotGlow-ESP32

DotGlow-ESP32 bill of materials (BOM)

35 components, 32 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1-N16R8
ESPRESSIF(乐鑫)
U1
1
XL-B1515RGBA-HF
XC6220B331MR-G
XINGLIGHT(成兴光)
U2
1
74AHCT125
U3
1
MAX98357A
U4
1
USBLC6-2SC6
U5
1
USB-C 5V
J1
1
DISPLAY IN
J2
1
DHT22
J3
1
I2C (RTC V2)
J4
1
SPEAKER 8R 2W
J5
1
LDR
J6
1
STOPWATCH SW
J7
1
NTC 10k
RT1
1
TSB001A3512A
RESET
BZCN(博众电气)
SW1
1
TSB001A3512A
BOOT
BZCN(博众电气)
SW2
1
STOPWATCH
SW3
1
SS34
Power LED
MDD(辰达半导体)
D1
2
CC0805KRX7R9BB104
22uF 10V
YAGEO(国巨)
C1, C2
1
TCC0805X7R105K500DTS
100nF
CCTC(三环)
C3
1
GRM21BR61H106KE43L
1uF
muRata(村田)
C4
Show 12 more
QtyPartRefs
1
GRM21BR61H106KE43L
10uF 10V
muRata(村田)
C5
1
CC0805KRX7R9BB104
100nF
YAGEO(国巨)
C6
2
GRM21BR61H106KE43L
100nF
muRata(村田)
C7, C8
1
RC0805FR-07100RL
10k
YAGEO(国巨)
R1
1
RC0805FR-07100RL
100k
YAGEO(国巨)
R3
1
0805W8F5101T5E
10k
UNI-ROYAL(厚声)
R4
1
0805W8F1003T5E
10k
UNI-ROYAL(厚声)
R5
2
0805W8F5101T5E
4.7k
UNI-ROYAL(厚声)
R6, R7
1
0805W8F1002T5E
10k
UNI-ROYAL(厚声)
R8
1
0805W8F1002T5E
5.1k
UNI-ROYAL(厚声)
R9
1
FRC0805F4701TS
5.1k
FOJAN(富捷)
R10
1
FRC0805F4701TS
1k
FOJAN(富捷)
R11

DotGlow-ESP32 design files

The KiCad project lives in the ElectroIoT/DotGlow-ESP32 repository on GitHub; these links point at the commit this page was built from.

DotGlow-ESP32: common questions

What microcontroller does the DotGlow-ESP32 use?

The DotGlow-ESP32 is built around the ESP32-S3-WROOM-1-N16R8, from the ESP32 family.

How big is the DotGlow-ESP32 PCB?

The DotGlow-ESP32 measures 128 × 33 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the DotGlow-ESP32?

35 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the DotGlow-ESP32 design files?

From the ElectroIoT/DotGlow-ESP32 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the DotGlow-ESP32 design in my own project?

Yes, under the terms of its MIT license, which ElectroIoT chose for the repository.

Can I test firmware for the DotGlow-ESP32 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards