Flipper subg
About the Flipper subg PCB
Flipper subg is an open source PCB design by ElectronicCats, published on GitHub. It is a 4-layer board measuring 67 × 31.3 mm, with 41 components from 28 distinct parts.
Other key parts include the SX1262IMLTRT, CC1101RGPR, 0900FM15D0039, 0915BM15A0001E and PE42421. By type, the board carries 16 capacitors, 8 resistors, 5 ICs, 4 antennas, 3 inductors and 2 crystals.
It belongs with the rf & radio and dev boards & breakouts designs in this gallery.
From the project
Flipper addons by Electronic Cats
This addon in addition to adding an extra CC1101 to our beloved Flipper adds a LoRa SX1272 chip that will allow to analyze and view IoT traffic in the SubGigaHz band.
Main components on the Flipper subg
Flipper subg bill of materials (BOM)
41 components, 28 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | SX1262IMLTRT | QFN-24-1EP_4x4mm_P0.5mm_EP2.65x2.65mm | U1 |
| 1 | CC1101RGPR | QFN-20-1EP_4x4mm_P0.5mm_EP2.5x2.5mm_ThermalVias | U2 |
| 1 | 0900FM15D0039 | 0900FM15D0039E | U3 |
| 1 | 0915BM15A0001E | 0915BM15A0001E | U4 |
| 1 | PE42421 | SOT-363_SC-70-6 | U5 |
| 1 | 32MHZ 32Mhz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y1 |
| 1 | 26MHZ 26Mhz | Crystal_SMD_2520-4Pin_2.5x2.0mm | Y2 |
| 1 | CONN_01X10_SOCKET Conn_01x10_Socket | PinHeader_1x10_P2.54mm_Vertical | J1 |
| 1 | CONN_01X08_SOCKET Conn_01x08_Socket | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 2 | Antenna | Texas_SWRA416_868MHz_915MHz | AE1, AE2 |
| 1 | Antenna_Shield | CONN1_U.FL-R-SMT-180_HIR | AE3 |
| 1 | u.fl | CONN1_U.FL-R-SMT-180_HIR | AE4 |
| 1 | LED | LED_0805_2012Metric | D1 |
| 1 | 15UH 15uH | L_0603_1608Metric | L1 |
| 1 | 47NH 47nH | L_0603_1608Metric | L2 |
| 1 | 9.1NH 9.1nH | L_0603_1608Metric | L3 |
| 6 | 0.1UF 0.1uF | C_0603_1608Metric | C1, C2, C5, C8, C9, C10 |
| 2 | 27PF 27pF | C_0603_1608Metric | C3, C6 |
| 1 | 470NF 470nF | C_0603_1608Metric | C4 |
| 1 | 47PF 47pF | C_0603_1608Metric | C7 |
Show 8 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 10UF 10uF | C_0603_1608Metric | C11 |
| 2 | 1NF 1nF | C_0603_1608Metric | C12, C14 |
| 1 | 100PF 100pF | C_0603_1608Metric | C13 |
| 2 | 3.3PF 3.3pF | C_0603_1608Metric | C15, C16 |
| 1 | 56K | R_0603_1608Metric | R1 |
| 2 | 100R | R_0603_1608Metric | R2, R4 |
| 1 | 1K | R_0805_2012Metric | R3 |
| 4 | 0 | R_0402_1005Metric | R5, R6, R7, R8 |
Flipper subg design files
The KiCad project lives in the ElectronicCats/flipper-addons repository on GitHub; these links point at the commit this page was built from.
Flipper subg: common questions
How big is the Flipper subg PCB?
The Flipper subg measures 67 × 31.3 mm, has 4 copper layers and is 1.6 mm thick.
How many components are on the Flipper subg?
41 components, from 28 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Flipper subg design files?
From the ElectronicCats/flipper-addons repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Flipper subg design in my own project?
The repository has no license, so all rights stay with ElectronicCats. Use it as a reference, and ask the author before reusing the design.
More boards in flipper-addons
ESP32Marauder
67 × 28 mm31 parts2LNo license130
ESP32Marauder spoof
75 × 74.7 mm26 parts2LNo license130
FLIPPER ETHERNET
67 × 25 mm25 parts2LNo license130
CANBUS Flipper
67 × 21.3 mm24 parts2LNo license130
FLIPPER MOD BUS
62.8 × 23.2 mm15 parts2LNo license130
Flipper UWB
34 × 67 mm13 parts2LNo license130
Mags
66 × 73.1 mm10 parts2LNo license130
Similar boards
88 Pin Vag Breakout
rusefi
142 × 58 mm91 parts2LGPL-3.01.2k
134pin 7-967288-1
139.7 × 73.7 mm38 parts2LGPL-3.01.2k
Breakout 60pin EEC-IV
139.7 × 62.2 mm15 parts2LGPL-3.01.2k
Breakout 112pin Connector
174 × 58 mm39 parts2LGPL-3.01.2k
Eecv breakout
140.8 × 53.7 mm9 parts4LGPL-3.01.2k
Rj45 breakout
rene-dev
15.2 × 53.8 mm3 parts2LGPL-3.0979