H0
eljotx·SDR-TRX-on-ESP32-A1S·kickad/v10/h0/h0.kicad_pcb
About the H0 PCB
H0 is an open source ESP32 PCB design by eljotx, published on GitHub. It is a 2-layer board measuring 137 × 63 mm, with 116 components from 59 distinct parts.
Its main chip is the ESP32-A1S, from the ESP32 family. Other key parts include the ILI9341 and LM386. By type, the board carries 40 resistors, 30 capacitors, 11 connectors, 10 switches, 5 transistors and 5 diodes.
It belongs with the rf & radio and displays & leds designs in this gallery.
From the project
This repository describes an SDR transceiver based on the ESP32 A1S processor, using an ILI9341 color touchscreen display, and a Si5351 oscillator. The program was written on the Arduino platform and is still in development, but the most important features have already been implemented and tested.
Main components on the H0
H0 bill of materials (BOM)
116 components, 59 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ILI9341 | ili9342 | U1 |
| 1 | LM386 | Diodes_PSOP-8 | U2 |
| 2 | ~ | dc-dc | U3, U4 |
| 1 | ESP32-A1S | ESP32-A1S | MOD1 |
| 4 | BC847 | SOT-23 | Q1, Q2, Q3, Q4 |
| 1 | BC807 | SOT-23 | Q5 |
| 1 | Prgrm | PinHeader_1x07_P2.54mm_Vertical | J1 |
| 1 | Conn_01x05 | PinHeader_1x05_P2.54mm_Vertical | J2 |
| 1 | Spk | power_con | J3 |
| 1 | Pol | PinHeader_1x02_P2.54mm_Vertical | J4 |
| 1 | Mic | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | +12V | power_con | J6 |
| 1 | Q | SMA_Amphenol_901-144_Vertical | J7 |
| 1 | I | SMA_Amphenol_901-144_Vertical | J8 |
| 1 | Keying | PinHeader_1x04_P2.54mm_Vertical | J9 |
| 1 | Conn_01x09 | PinHeader_1x09_P2.54mm_Vertical | J10 |
| 1 | Aux | PinHeader_1x03_P2.54mm_Vertical | J11 |
| 2 | 100k | Potentiometer_ACP_CA6-H2,5_Horizontal | Arw_1, Arwd1 |
| 2 | 10k | Potentiometer_ACP_CA6-H2,5_Horizontal | Bal1, RV1 |
| 3 | EC2-4.5NU | Relay_DPDT_Kemet_EC2_NJ | K1, K2, K3 |
Show 39 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 100 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV2 |
| 1 | Reset | microswitch | SW1 |
| 1 | Cnt | RotaryEncoder_Alps_EC11E-Switch_Vertical_H20mm | SW2 |
| 1 | Step | microswitch | SW3 |
| 1 | Up/Dn | microswitch | SW4 |
| 1 | Rit | microswitch | SW5 |
| 1 | Save | microswitch | SW6 |
| 1 | Rest | microswitch | SW7 |
| 1 | Prgm | microswitch | SW8 |
| 1 | Mnu | microswitch | SW9 |
| 1 | F1/F2 | microswitch | SW11 |
| 1 | 22k | Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | Vol1 |
| 1 | 1k | Potentiometer_Alpha_RD901F-40-00D_Single_Vertical | Vol2 |
| 1 | 1N4007 | D_2114_3652Metric | D1 |
| 2 | D | C_1206_3216Metric | D2, D3 |
| 1 | 3.3V | D_DO-34_SOD68_P10.16mm_Horizontal | D4 |
| 1 | 3.3V | C_1206_3216Metric | D5 |
| 11 | 10u | C_1206_3216Metric | C1, C5, C6, C7, C8, C10, C18, C24 +3 |
| 4 | 47u | CP_EIA-7343-31_Kemet-D | C2, C11, C12, C19 |
| 6 | 0.1u | C_0805_2012Metric | C3, C4, C13, C14, C23, C27 |
| 5 | 4.7n | C_0805_2012Metric | C9, C15, C16, C17, C26 |
| 3 | 10n | C_0805_2012Metric | C20, C21, C22 |
| 1 | 10u | CP_EIA-7343-31_Kemet-D | C30 |
| 11 | 10k | R_0805_2012Metric | R1, R2, R9, R10, R22, R23, R24, R26 +3 |
| 6 | 4.7k | R_0805_2012Metric | R3, R14, R15, R17, R20, R35 |
| 1 | 15k | R_0805_2012Metric | R4 |
| 1 | 7.5k | R_0805_2012Metric | R5 |
| 1 | 3.6k | R_0805_2012Metric | R6 |
| 1 | 1.6k | R_0805_2012Metric | R7 |
| 3 | 470 | R_0805_2012Metric | R8, R29, R31 |
| 1 | 10 | R_0805_2012Metric | R11 |
| 5 | 1k | R_0805_2012Metric | R12, R13, R30, R37, R38 |
| 2 | 5.1k | R_0805_2012Metric | R16, R40 |
| 1 | 12k | R_0805_2012Metric | R18 |
| 1 | 24k | R_0805_2012Metric | R19 |
| 1 | 1.2k | R_0805_2012Metric | R21 |
| 1 | 56k | R_0805_2012Metric | R25 |
| 1 | 51k | R_0805_2012Metric | R28 |
| 3 | 3.3k | R_0805_2012Metric | R32, R34, R39 |
H0 design files
The KiCad project lives in the eljotx/SDR-TRX-on-ESP32-A1S repository on GitHub; these links point at the commit this page was built from.
- Layoutkickad/v10/h0/h0.kicad_pcb
- Schematickickad/v10/h0/h0.kicad_sch
H0: common questions
What microcontroller does the H0 use?
The H0 is built around the ESP32-A1S, from the ESP32 family.
How big is the H0 PCB?
The H0 measures 137 × 63 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the H0?
116 components, from 59 distinct parts. The full bill of materials is listed on this page.
Where can I download the H0 design files?
From the eljotx/SDR-TRX-on-ESP32-A1S repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the H0 design in my own project?
The repository has no license, so all rights stay with eljotx. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the H0 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
More boards in SDR-TRX-on-ESP32-A1S
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k