Ha
eljotx·SDR-TRX-on-ESP32-A1S·kickad/v11/ha/ha.kicad_pcb
About the Ha PCB
Ha is an open source PCB design by eljotx, published on GitHub. It is a 2-layer board measuring 137 × 63 mm, with 135 components from 48 distinct parts.
Other key parts include the FST3253, Si5351, Dc-Dc, NE5534 and NE5532. By type, the board carries 44 capacitors, 44 resistors, 12 diodes, 11 ICs, 8 connectors and 5 transistors.
It belongs with the rf & radio and displays & leds designs in this gallery.
From the project
This repository describes an SDR transceiver based on the ESP32 A1S processor, using an ILI9341 color touchscreen display, and a Si5351 oscillator. The program was written on the Arduino platform and is still in development, but the most important features have already been implemented and tested.
The system can be operated in a basic configuration without the AGC system and redundant components. The drawing shows which components do not need to be installed in such a case. The red markings refer to the PIN diode attenuator. The purple markings refer to the input amplifier, which results in reduced receiver sensitivity. In both cases, the jumpers marked in blue must be installed.

Main components on the Ha
Ha bill of materials (BOM)
135 components, 48 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | FST3253 | SOIC-16W_5.3x10.2mm_P1.27mm | U1 |
| 1 | Si5351 | Si5351 | U2 |
| 1 | Dc-Dc | dc-dc | U3 |
| 2 | NE5534 | SO-8_3.9x4.9mm_P1.27mm | U4, U5 |
| 2 | NE5532 | SO-8_3.9x4.9mm_P1.27mm | U6, U7 |
| 1 | Mar6 | Era | U8 |
| 1 | PCF8574AT | SOIC-16W_7.5x10.3mm_P1.27mm | U9 |
| 1 | 74AC74 | SO-14_5.3x10.2mm_P1.27mm | U10 |
| 1 | 74AC86 | SO-14_5.3x10.2mm_P1.27mm | U11 |
| 4 | BC847 | SOT-23 | Q1, Q2, Q3, Q5 |
| 1 | BC807 | SOT-23 | Q4 |
| 1 | Signal | PinHeader_2x09_P2.54mm_Vertical | J1 |
| 1 | RF | SMA_Amphenol_901-144_Vertical | J2 |
| 1 | F1sw | PinHeader_1x03_P2.54mm_Vertical | J3 |
| 1 | F01sw | PinHeader_1x03_P2.54mm_Vertical | J4 |
| 1 | F00sw | PinHeader_1x03_P2.54mm_Vertical | J5 |
| 1 | Sh | PinHeader_1x02_P2.54mm_Vertical | J6 |
| 1 | Q | SMA_Amphenol_901-144_Vertical | J7 |
| 1 | I | SMA_Amphenol_901-144_Vertical | J8 |
| 2 | EC2-4.5NU | Relay_DPDT_Kemet_EC2_NJ | K1, K3 |
Show 28 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 220 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV1 |
| 1 | Att1 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV2 |
| 1 | Att2 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV3 |
| 1 | Att3 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV4 |
| 1 | Att4 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV5 |
| 1 | Att5 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV6 |
| 1 | Att6 | Potentiometer_ACP_CA6-H2,5_Horizontal | RV7 |
| 1 | 100k | Potentiometer_ACP_CA6-H2,5_Horizontal | RV8 |
| 4 | BAR65 | C_0805_2012Metric | D1, D2, D3, D4 |
| 8 | D | C_1206_3216Metric | D5, D6, D7, D8, D9, D10, D11, D12 |
| 1 | 4.7uH | L_Axial_L5.3mm_D2.2mm_P7.62mm_Horizontal_Vishay_IM-1 | L1 |
| 24 | 0.1u | C_0805_2012Metric | C1, C2, C3, C4, C5, C6, C7, C11 +16 |
| 4 | 4.7n | C_0805_2012Metric | C8, C9, C10, C21 |
| 4 | 47u | CP_EIA-7343-31_Kemet-D | C12, C13, C18, C19 |
| 4 | 4.7nF | C_0805_2012Metric | C15, C16, C17, C20 |
| 8 | 10uF | C_1206_3216Metric | C34, C35, C36, C37, C38, C39, C40, C41 |
| 15 | 10k | R_0805_2012Metric | R1, R2, R3, R8, R9, R10, R11, R12 +7 |
| 8 | 100 | R_0805_2012Metric | R4, R5, R6, R7, R23, R24, R25, R26 |
| 2 | 5.1k | R_0805_2012Metric | R16, R22 |
| 2 | 3.3k | R_0805_2012Metric | R19, R20 |
| 3 | 51k | R_0805_2012Metric | R21, R28, R42 |
| 4 | 1k | R_0805_2012Metric | R27, R30, R33, R38 |
| 3 | 750 | R_0805_2012Metric | R29, R37, R40 |
| 2 | 330 | R_0805_2012Metric | R31, R32 |
| 1 | 560 | R_0805_2012Metric | R35 |
| 1 | 0 | R_0805_2012Metric | R36 |
| 2 | 51 | R_0805_2012Metric | R39, R41 |
| 1 | 220 | R_0805_2012Metric | R44 |
Ha design files
The KiCad project lives in the eljotx/SDR-TRX-on-ESP32-A1S repository on GitHub; these links point at the commit this page was built from.
- Layoutkickad/v11/ha/ha.kicad_pcb
- Schematickickad/v11/ha/ha.kicad_sch
Ha: common questions
How big is the Ha PCB?
The Ha measures 137 × 63 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Ha?
135 components, from 48 distinct parts. The full bill of materials is listed on this page.
Where can I download the Ha design files?
From the eljotx/SDR-TRX-on-ESP32-A1S repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Ha design in my own project?
The repository has no license, so all rights stay with eljotx. Use it as a reference, and ask the author before reusing the design.
More boards in SDR-TRX-on-ESP32-A1S
Similar boards
BM28B0.6-24DSBreakout
scottbez1
15.2 × 35.6 mm3 parts2LApache-2.022.2kLevelShifterBreakout
scottbez1
15.2 × 20.3 mm5 parts2LApache-2.022.2kView base
scottbez1
81.2 × 81.2 mm81 parts2LApache-2.022.2kView screen
scottbez1
35 × 35 mm12 parts2LApache-2.022.2kDisplay eval
byrantech
52.1 × 22.6 mm12 parts4LMIT4.3kChainlinkBase
scottbez1
98.4 × 190.5 mm119 parts2LApache-2.04.2k