13 open source boards using the NE5534
Real designs built with the NE5534, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
RP2040/RP2350
Multislope-3I
NNNILabs
100 × 74 mm124 parts4LMIT43STM32
UsbSound
SteveSyfuhs
121.6 × 79.8 mm91 parts4LMIT12Nc1
nietamten
74.2 × 87.1 mm72 parts2LNo license4Piezo-9v
Supermagnum
70 × 54.5 mm26 parts2LCC0-1.04Actidamp mk4-smd
josko7452
119 × 100 mm199 parts4LNo license1Src multislope adc
Atmelfan
72.5 × 50 mm73 parts4LCERN-OHL-S-2.00Raspberry Pi
Sern
Heppokoyuki
100 × 100 mm67 parts2LNo license0Daughter-Board-Muses-Op-Amp
Gninnorg
140.3 × 65 mm38 parts2LNo license0Kip
GHawk1124
46 × 26 mm8 parts2LMIT0STM32
LimiterBoard
nietamten
40.1 × 38.3 mm45 parts2LNo license4Ha
eljotx
137 × 63 mm135 parts2LNo license2Lpf ak4497 dual mono
ljufa
69.9 × 33 mm31 parts2LMIT2Buffer-Opamp
Gninnorg
84 × 108 mm21 parts2LNo license0
How designs wire the NE5534
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the NE5534 connects to, and the resistors, capacitors and other passives placed on it.
- The - pin has a series resistor on 9 of 11 designs, most often 10 kΩ (then 100 Ω).
- Pin 6 has a series resistor on 9 of 11 designs, most often 39 kΩ (then 820 Ω).
- The BAL pin is left unconnected on 10 of 11 designs.
- The - pin has a series capacitor on 7 of 11 designs, most often 2.7 nF (then 100 nF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| BALpin 1 | Connected to: Not connected 91% | — |
| -pin 2 | Connected to: Signal 100% |
|
| +pin 3 | Connected to: Signal 64% · GND 36% |
|
| V-pin 4 | Connected to: -15V 45% · GND 18% · a signal 36% |
|
| COMPpin 5 | Connected to: Not connected 55% · a signal 36% |
|
| Pin 6 | Connected to: A connector 45% |
|
| V+pin 7 | Connected to: VCC 91% |
|
| C/Bpin 8 | Connected to: Not connected 55% · a signal 45% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Multislope-3I by NNNILabs, UsbSound by SteveSyfuhs, LimiterBoard by nietamten and Piezo-9v by Supermagnum.
The NE5534 in open source designs
The gallery holds 13 open source boards using the NE5534 from 11 GitHub repositories; a typical one measures about 84 × 65 mm and carries around 67 components.
69% are two-layer designs, the rest use four layers or more, and 46% carry an open source license.
The most starred is Multislope-3I by NNNILabs.
Parts used alongside the NE5534
Microcontrollers on boards using the NE5534
What boards using the NE5534 are built for
NE5534: common questions
Where can I find a NE5534 reference design?
Each of the 13 boards on this page is a real design using the NE5534. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the NE5534 - pin?
The - pin has a series resistor on 9 of 11 designs, most often 10 kΩ (then 100 Ω). Counted from the KiCad layouts of 11 open source designs using the NE5534.
What resistor goes on the NE5534 pin 6?
Pin 6 has a series resistor on 9 of 11 designs, most often 39 kΩ (then 820 Ω). Counted from the KiCad layouts of 11 open source designs using the NE5534.
How is the NE5534 BAL pin connected?
The BAL pin is left unconnected on 10 of 11 designs. Counted from the KiCad layouts of 11 open source designs using the NE5534.
Which microcontrollers do boards using the NE5534 use?
Most are built on STM32 (2), Raspberry Pi (1) and RP2040/RP2350 (1).
How big is a typical board using the NE5534?
The median is 84 × 65 mm, and 69% are two-layer designs.
What is the most popular open source board using the NE5534?
By GitHub stars, Multislope-3I by NNNILabs, with 43 stars.
Can I simulate one of these boards using the NE5534 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.