Portable gnss display

F45c·portable-gnss-display·pcb/GNSS_Display.kicad_pcb

Portable gnss display PCB layout, top view — open source ESP32 board by F45c

About the Portable gnss display PCB

Portable gnss display is an open source ESP32 PCB design by F45c, published on GitHub. It is a 2-layer board measuring 40.8 × 63.4 mm, with 41 components from 20 distinct parts.

Its main chip is the ESP32-C3, from the ESP32 family. Other key parts include the MCP1702T-3302E/CB and NEO-M9N. By type, the board carries 16 capacitors, 12 connectors, 7 resistors, 5 ICs and 1 inductor.

It belongs with the rf & radio and displays & leds designs in this gallery.

From the project

A Portable box displaying a satellite map of your current position

I downloaded a few tiles where I live and put them on an sd card. I had to censor the map mostly so I don't leak my address. The example image is below.

It's a very nice device but after all, I still use my phone more often than this.

(Redacted display because it shows my home location)

In the center, on the red + symbol is the gps position and on top is the N for north.

Portable gnss display, from the project README
From the project README

Main components on the Portable gnss display

Portable gnss display bill of materials (BOM)

41 components, 20 distinct parts — part numbers from the project's BOM.

QtyPartRefs
3
MCP1702T-3302E/CB
MCP1702T-3302E_CB
U2, U4, U5
1
ESP32-C3
U3
1
NEO-M9N
U6
1
Conn_Coaxial
J1
1
CONN_01X04_PIN
Conn_01x04_Pin
J2
2
CONN_01X04_SOCKET
Conn_01x04_Socket
J3, J6
1
USB_A
J4
1
TFT Display
J5
1
CONN_01X02_PIN
Conn_01x02_Pin
J7
1
USB4215-03-A_REVA
J8
2
Bridge ESP-NEO 3.3V
J9, J12
2
CONN_02X02_ODD_EVEN
Conn_02x02_Odd_Even
J10, J11
1
27NH
27nH
L2
7
100NF
100nF
C1, C3, C7, C8, C10, C13, C14
5
1UF
1uF
C2, C5, C9, C11, C16
4
10UF
10uF
C4, C6, C12, C15
1
10K
R1
3
22Ω
R2, R4, R5
1
100kΩ
R3
2
5.1Ω
R6, R7

Portable gnss display design files

The KiCad project lives in the F45c/portable-gnss-display repository on GitHub; these links point at the commit this page was built from.

Portable gnss display: common questions

What microcontroller does the Portable gnss display use?

The Portable gnss display is built around the ESP32-C3, from the ESP32 family.

How big is the Portable gnss display PCB?

The Portable gnss display measures 40.8 × 63.4 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Portable gnss display?

41 components, from 20 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Portable gnss display design files?

From the F45c/portable-gnss-display repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Portable gnss display design in my own project?

The repository has no license, so all rights stay with F45c. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Portable gnss display without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards