17 open source boards using the NEO-M9N
Real designs built with the NEO-M9N, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
VCU
sufst
194.3 × 92.8 mm205 parts4LGPL-3.019ESP32
Hw sensor
larus-breeze
120 × 74.6 mm215 parts4LCustom license14ESP32
Mesh hand
sneakylizard123-4
50 × 75 mm67 parts4LNo license8Power Unit - CanSat 2023
Project-SkyFall
60.7 × 61.3 mm153 parts4LNo license6Feather-NEO-M9N-GPS
averywallis
50.8 × 22.9 mm37 parts2LGPL-3.06ESP32
Chronos phantom
jayis1
65 × 30 mm26 parts4LNo license3STM32
SDM-24 Data Logger
sundevilmotorsports
101 × 75 mm110 parts4LNo license2- schematic only · 7 partsRP2040/RP2350
Steganon-1
VAIBHAV3129
7 partsMIT1 RP2040/RP2350
4in gps
sonicavionics
84.1 × 61.7 mm84 parts4LMIT0STM32
Flight-Computer
jainamnahar14surat
50 × 50 mm72 parts6LMIT0ESP32
Gps logger
kaushalch1
96.5 × 71 mm47 parts2LNo license0ESP32
Portable gnss display
F45c
40.8 × 63.4 mm41 parts2LNo license0GPSM9N
Raetti
55.5 × 41.5 mm13 parts4LNo license0RISC-V
CyberTastic
wrickert
88.1 × 44.6 mm60 parts2LNo license8Power Unit 2
Project-SkyFall
60.7 × 61.3 mm92 parts4LNo license6STM32
NAVIG
Arav0001
78 × 78 mm66 parts4LMIT1NavIC GNSS
Chirag-Vadrali
35 × 35 mm19 parts4LNo license1
How designs wire the NEO-M9N
Read from the KiCad layouts of 14 open source designs, one per repository: what each pin of the NEO-M9N connects to, and the resistors, capacitors and other passives placed on it.
- The RESERVED pins is left unconnected on 98% of them.
- The RF_IN pin has a inductor on 10 of 14 designs, most often 27 nH (then 33 nH).
- The VCC pin has a decoupling capacitor on 10 of 14 designs, most often 1 µF (then 100 nF).
- The LNA_EN pin is left unconnected on 10 of 14 designs (a signal on 4).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| EXTINTpin 4 | Connected to: Not connected 64% · a signal 36% | — |
| VCC_RFpin 9 | Connected to: Signal 71% |
|
| GNDpin 10, 12, 13, 24 | Connected to: GND 88% | — |
| RF_INpin 11 | Connected to: A connector 43% |
|
| LNA_ENpin 14 | Connected to: Not connected 71% · a signal 29% | — |
| RESERVEDpin 15, 16, 17 | Connected to: Not connected 98% | — |
| V_BCKPpin 22 | Connected to: 3.3V 50% · a signal 43% |
|
| VCCpin 23 | Connected to: 3.3V 86% |
|
11 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include VCU by sufst, Hw sensor by larus-breeze, Mesh hand by sneakylizard123-4 and CyberTastic by wrickert.
The NEO-M9N in open source designs
The gallery holds 17 open source boards using the NEO-M9N from 16 GitHub repositories; a typical one measures about 62.8 × 61.5 mm and carries around 66 components.
75% use four copper layers or more, and 35% carry an open source license.
The most starred is VCU by sufst.
Parts used alongside the NEO-M9N
Microcontrollers on boards using the NEO-M9N
What boards using the NEO-M9N are built for
NEO-M9N: common questions
Where can I find a NEO-M9N reference design?
Each of the 17 boards on this page is a real design using the NEO-M9N. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the NEO-M9N RESERVED pin connected?
The RESERVED pins is left unconnected on 98% of them. Counted from the KiCad layouts of 14 open source designs using the NEO-M9N.
How is the NEO-M9N RF_IN pin connected?
The RF_IN pin has a inductor on 10 of 14 designs, most often 27 nH (then 33 nH). Counted from the KiCad layouts of 14 open source designs using the NEO-M9N.
What decoupling capacitors do designs use on the NEO-M9N VCC pin?
The VCC pin has a decoupling capacitor on 10 of 14 designs, most often 1 µF (then 100 nF). Counted from the KiCad layouts of 14 open source designs using the NEO-M9N.
What parts are used alongside the NEO-M9N?
The USBLC6-2SC6, AMS1117-3.3, AP2112K-3.3, BNO055 and ER_OLEDM0.91_1x-I2C appear in the most repositories here.
Which microcontrollers do boards using the NEO-M9N use?
Most are built on ESP32 (6), STM32 (3), RP2040/RP2350 (2) and RISC-V (1).
How big is a typical board using the NEO-M9N?
The median is 62.8 × 61.5 mm, and 25% are two-layer designs.
What is the most popular open source board using the NEO-M9N?
By GitHub stars, VCU by sufst, with 19 stars.
Can I simulate one of these boards using the NEO-M9N before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.