RGB-Lamp
F9Motion·RGB-Lamp·Kicad and blend file/RGB LAMP/RGB LAMP.kicad_pcb
About the RGB-Lamp PCB
RGB-Lamp is an open source ESP32 PCB design by F9Motion, published on GitHub. It is a 2-layer board measuring 70 × 70 mm, with 16 components from 9 distinct parts.
Its main chip is the ESP32-C3-DevKitM-1, from the ESP32 family. Other key parts include the ER_OLEDM0.91_1x-I2C, MCP73831-2-MC and MT3608. By type, the board carries 4 ICs, 4 diodes, 4 resistors, 2 switches, 1 connector and 1 battery holder.
From the project
Custom RGB Lamp
Main components on the RGB-Lamp
RGB-Lamp bill of materials (BOM)
16 components, 9 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ER_OLEDM0.91_1x-I2C | ER_OLEDM0.91_1x-I2C | U1 |
| 1 | ESP32-C3-DevKitM-1 | ESP32-C3-DevKitM-1 | U2 |
| 1 | MCP73831-2-MC | DFN-8-1EP_3x2mm_P0.5mm_EP1.7x1.4mm | U3 |
| 1 | MT3608 | SOT-23-6 | U4 |
| 1 | USB_C_Receptacle_USB2.0_16P | USB_C_Receptacle_HCTL_HC-TYPE-C-16P-01A | J1 |
| 1 | Battery_Cell | JST_PH_S2B-PH-K_1x02_P2.00mm_Horizontal | BT1 |
| 2 | SW_Push | SW_PUSH_6mm | SW1, SW2 |
| 4 | WS2812B | LED_WS2812B_PLCC4_5.0x5.0mm_P3.2mm | D1, D2, D3, D4 |
| 4 | R_Small | R_0805_2012Metric | R1, R2, R3, R4 |
RGB-Lamp design files
The KiCad project lives in the F9Motion/RGB-Lamp repository on GitHub; these links point at the commit this page was built from.
RGB-Lamp: common questions
What microcontroller does the RGB-Lamp use?
The RGB-Lamp is built around the ESP32-C3-DevKitM-1, from the ESP32 family.
How big is the RGB-Lamp PCB?
The RGB-Lamp measures 70 × 70 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the RGB-Lamp?
16 components, from 9 distinct parts. The full bill of materials is listed on this page.
Where can I download the RGB-Lamp design files?
From the F9Motion/RGB-Lamp repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the RGB-Lamp design in my own project?
The repository has no license, so all rights stay with F9Motion. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the RGB-Lamp without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k