32 open source boards using the MCP73831-2-MC
Real designs built with the MCP73831-2-MC, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
ESP32
Oniondao badge
OnionDAO-git
76.6 × 141.1 mm116 parts2LNo license17OpenIEMA
aaravjhamb
40 × 69.8 mm53 parts2LNo license6Nordic nRF
Apex
HashirX-ux
516.6 × 112.1 mm478 parts4LMIT2ESP32
Solana badge
spacemandev-git
77.6 × 116.3 mm81 parts2LNo license2Nexus
HashirX-ux
133.5 × 86 mm70 parts2LMIT2ESP32
Minion
vibsthebot
60 × 60 mm77 parts4LNo license1STM32
Main-Module
Rowan-Rocketry
76.2 × 48.3 mm49 parts4LNo license1ESP32
Mk oniondao badge
majeedkhori
76.6 × 141.1 mm116 parts2LNo license0STM32
Chickensticks
npgo22
42 × 100 mm96 parts4LNo license0ESP32
SkyRizz-ESPSOL
SkyRizzAI
40.6 × 40.6 mm70 parts2LCERN-OHL-S-2.00STM32
Microbot
Rishabh416
42.3 × 42.3 mm68 parts2LNo license0ESP32
ESP32-C3-Low-Power-IoT-Plant-Node
mohamed-sebbar
59.5 × 29.9 mm65 parts4LCERN-OHL-W-2.00Air780eg cellular modem board
manhoosbilli1
30.2 × 27 mm62 parts2LNo license0ESP32
Rf detector
joshitha-c
71 × 150.5 mm57 parts2LNo license0ESP32
Wireless-Environmental-Parameter-Transmitter
tomasikjulia-code
66.5 × 24.5 mm54 parts4LNo license0ESP32
Esp32-bluetooth erm accel dongle faulty
manhoosbilli1
23.3 × 28.4 mm50 parts4LNo license0ESP32
Esp32-dongle v0-1-ceramic antenna
manhoosbilli1
11 × 50.8 mm47 parts4LNo license0Nordic nRF
EyeReader
M7md0010
52.7 × 15 mm44 parts4LNo license0Daron necklace bottom board
manhoosbilli1
20 × 20 mm42 parts2LNo license0ESP32
Electrone shelving
F9Motion
52.6 × 52.6 mm21 parts2LNo license0RP2040/RP2350
Smart coaster-
EveyKay
69 × 77 mm19 parts2LNo license0RP2040/RP2350
GameBro
F9Motion
140 × 62 mm18 parts2LNo license0ESP32
RGB-Lamp
F9Motion
70 × 70 mm16 parts2LNo license0RP2040/RP2350
Headphone holder
F9Motion
85.6 × 85.6 mm13 parts2LNo license0- schematic only · 41 partsESP32
Ereader
katetriestocode
41 partsNo license0 STM32
Pyro-Module
Rowan-Rocketry
76.2 × 48.3 mm49 parts4LNo license1STM32
Wearable som
ray4477
40.3 × 40 mm48 parts4LMIT0STM32
Radio-Module
Rowan-Rocketry
76.2 × 48.3 mm49 parts4LNo license1STM32
Wearables v2
ray4477
40.3 × 40 mm47 parts2LMIT0STM32
Recovery-Module
Rowan-Rocketry
76.2 × 48.3 mm49 parts4LNo license1STM32
Chickenstick
npgo22
42 × 100 mm96 parts4LNo license0STM32
Chickenstick
npgo22
42 × 100 mm96 parts4LNo license0
How designs wire the MCP73831-2-MC
Read from the KiCad layouts of 27 open source designs, one per repository: what each pin of the MCP73831-2-MC connects to, and the resistors, capacitors and other passives placed on it.
- The PROG pin has a resistor to GND on 24 of 27 designs, most often 10 kΩ (then 2 kΩ).
- The EP pin is left unconnected on 20 of 27 designs (GND on 7).
- The VBAT pins have a capacitor to GND on 16 of 27 designs, most often 4.7 µF (then 10 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| VDDpin 1, 2 | Connected to: VBUS 74% · a signal 26% |
|
| VBATpin 3, 4 | Connected to: A connector 33% · VBAT 41% |
|
| VSSpin 6 | Connected to: GND 89% | — |
| NCpin 7 | Connected to: Not connected 100% | — |
| PROGpin 8 | Connected to: Signal 100% |
|
| EPpin 9 | Connected to: Not connected 74% · GND 26% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Oniondao badge by OnionDAO-git, OpenIEMA by aaravjhamb, Apex by HashirX-ux and Nexus by HashirX-ux.
The MCP73831-2-MC in open source designs
The gallery holds 32 open source boards using the MCP73831-2-MC from 28 GitHub repositories; a typical one measures about 60 × 52.6 mm and carries around 52 components.
52% are two-layer designs, the rest use four layers or more, and 19% carry an open source license.
The most starred is Oniondao badge by OnionDAO-git.
Parts used alongside the MCP73831-2-MC
Microcontrollers on boards using the MCP73831-2-MC
What boards using the MCP73831-2-MC are built for
MCP73831-2-MC: common questions
Where can I find a MCP73831-2-MC reference design?
Each of the 32 boards on this page is a real design using the MCP73831-2-MC. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
What resistor goes on the MCP73831-2-MC PROG pin?
The PROG pin has a resistor to GND on 24 of 27 designs, most often 10 kΩ (then 2 kΩ). Counted from the KiCad layouts of 27 open source designs using the MCP73831-2-MC.
How is the MCP73831-2-MC EP pin connected?
The EP pin is left unconnected on 20 of 27 designs (GND on 7). Counted from the KiCad layouts of 27 open source designs using the MCP73831-2-MC.
How is the MCP73831-2-MC VBAT pin connected?
The VBAT pins have a capacitor to GND on 16 of 27 designs, most often 4.7 µF (then 10 µF). Counted from the KiCad layouts of 27 open source designs using the MCP73831-2-MC.
What parts are used alongside the MCP73831-2-MC?
The USBLC6-2SC6, CH340C, ER_OLEDM0.91_1x-I2C, ESP32-S3-WROOM-1 and ME6211C33M5 appear in the most repositories here.
Which microcontrollers do boards using the MCP73831-2-MC use?
Most are built on ESP32 (13), STM32 (10), RP2040/RP2350 (3) and Nordic nRF (2).
How big is a typical board using the MCP73831-2-MC?
The median is 60 × 52.6 mm, and 52% are two-layer designs.
What is the most popular open source board using the MCP73831-2-MC?
By GitHub stars, Oniondao badge by OnionDAO-git, with 17 stars.
Can I simulate one of these boards using the MCP73831-2-MC before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.