Diy led spot step5

FaisalHussain95·esp32-espnow-led-spots·kicad/diy_led_spot/diy_led_spot_step5.kicad_pcb

Diy led spot step5 PCB layout, top view — open source ESP32 board by FaisalHussain95

About the Diy led spot step5 PCB

Diy led spot step5 is an open source ESP32 PCB design by FaisalHussain95, published on GitHub. It is a 2-layer board measuring 48 × 37 mm, with 13 components from 12 distinct parts.

Its main chip is the ESP32-C3_SUPERMINI_SMD, from the ESP32 family. Other key parts include the DCDCStepDown and PT4115. By type, the board carries 4 capacitors, 3 ICs, 1 diode, 1 inductor and 1 resistor.

It belongs with the iot & wireless designs in this gallery.

From the project

DIY 220VAC LED spot controller — ESP32-C3 + COB LED + PT4115 PWM dimming, NTC thermal protection, active fan cooling, ESP-NOW mesh. WiFi bridge for Home Assistant (MQTT).

Replacing 13 cheap 220V ceiling spots with custom COB LED units — dimmable, Home Assistant integrated, actively cooled, and wirelessly controlled over ESP-NOW.

I have 13 recessed spots installed across my ceiling. They were cheap 220V AC units with no heatsink — just a bare aluminium PCB glued to a plastic shell.

Opening one up tells the whole story: the driver circuit runs directly off mains voltage with no thermal management whatsoever.

Diy led spot step5, from the project README
From the project README

Main components on the Diy led spot step5

Diy led spot step5 bill of materials (BOM)

13 components, 12 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
DCDCStepDown
U1
1
PT4115
U2
1
ESP32-C3_SUPERMINI_SMD
U3
1
BX-XH2.54-2PZZ
-LED+1
1
C19269965
0.33 1W
Rs1
1
MX1.25-2P
TEMP1
1
SS36
D1
1
C167888
47uH 800mA
L1
1
C14858
100pF 50V
C1
2
C6119901
22uF 35V
C2, C4
1
C476766
100nF 50V
C3
1
C23186
5.1kΩ 100mW
R1

Diy led spot step5 design files

The KiCad project lives in the FaisalHussain95/esp32-espnow-led-spots repository on GitHub; these links point at the commit this page was built from.

Diy led spot step5: common questions

What microcontroller does the Diy led spot step5 use?

The Diy led spot step5 is built around the ESP32-C3_SUPERMINI_SMD, from the ESP32 family.

How big is the Diy led spot step5 PCB?

The Diy led spot step5 measures 48 × 37 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Diy led spot step5?

13 components, from 12 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Diy led spot step5 design files?

From the FaisalHussain95/esp32-espnow-led-spots repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Diy led spot step5 design in my own project?

The repository has no license, so all rights stay with FaisalHussain95. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Diy led spot step5 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in esp32-espnow-led-spots

Similar boards