17 open source boards using the PT4115
Real designs built with the PT4115, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
CCFL2LED
mijuc
55 × 90 mm57 parts2LGPL-3.07ESP32
Pet filter
ZanzyTHEbar
110 × 80 mm52 parts2LNo license1ZLight CC2652
paoloach
100 × 100 mm42 parts2LApache-2.013w rgb led driver
tunaerray
65.1 × 46.1 mm24 parts2LNo license1ESP32
LuminousSaucer
paoloach
77 × 41 mm18 parts2LApache-2.01ESP32
Control board
Weepfrog
3 × 3 mm625 parts4LNo license0ESP8266
RGBW-Lampe
martinclausen2
99.6 × 69.6 mm155 parts2LNo license0Power
Edgeworth
90 × 27 mm60 parts2LNo license02x2x4-LED-Panel
irampton
75 × 30 mm56 parts2LMIT0ESP32
Diy led spot routed
FaisalHussain95
55.5 × 55.5 mm30 parts2LNo license024V-Constant-Current-LED-Driver
rohan21032003
40.7 × 18.4 mm17 parts2LNo license0PT4115 MiniBoard
maltejahn
27 × 16.3 mm13 parts2LNo license0- schematic only · 50 partsRaspberry Pi
Robot hexapode
lucas-minaberry
50 partsCustom license0 12x8 Led Array 9mm pitch
Weepfrog
173.7 × 137.7 mm307 parts4LNo license0Diy led spot
FaisalHussain95
50.5 × 47.5 mm26 parts2LNo license0Diy led spot step3
FaisalHussain95
50.5 × 47.5 mm26 parts2LNo license0ESP32
Diy led spot step5
FaisalHussain95
48 × 37 mm13 parts2LNo license0
How designs wire the PT4115
Read from the KiCad layouts of 11 open source designs, one per repository: what each pin of the PT4115 connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 10 of 11 designs, most often 68 µH (then 47 µH).
- The CSN pin has a pull-up to 12V on 8 of 11 designs, most often 1 Ω (then 150 mΩ).
- The DIM pin has a resistor to GND on 5 of 11 designs, most often 10 kΩ (then 5.1 kΩ).
- The VIN pin has a decoupling capacitor on 5 of 11 designs, most often 100 µF (then 2.2 µF).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 91% | — |
| DIMpin 3 | Connected to: Signal 100% |
|
| CSNpin 4 | Connected to: A connector 55% |
|
| VINpin 5 | Connected to: 12V 91% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include CCFL2LED by mijuc, LuminousSaucer by paoloach, ZLight CC2652 by paoloach and 3w rgb led driver by tunaerray.
The PT4115 in open source designs
The gallery holds 17 open source boards using the PT4115 from 13 GitHub repositories; a typical one measures about 60.3 × 46.8 mm and carries around 42 components.
88% are two-layer designs, the rest use four layers or more, and 24% carry an open source license.
The most starred is CCFL2LED by mijuc.
Parts used alongside the PT4115
Microcontrollers on boards using the PT4115
What boards using the PT4115 are built for
PT4115: common questions
Where can I find a PT4115 reference design?
Each of the 17 boards on this page is a real design using the PT4115. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the PT4115 SW pin connected?
The SW pin has a inductor on 10 of 11 designs, most often 68 µH (then 47 µH). Counted from the KiCad layouts of 11 open source designs using the PT4115.
What pull-up resistor is used on the PT4115 CSN pin?
The CSN pin has a pull-up to 12V on 8 of 11 designs, most often 1 Ω (then 150 mΩ). Counted from the KiCad layouts of 11 open source designs using the PT4115.
What resistor goes on the PT4115 DIM pin?
The DIM pin has a resistor to GND on 5 of 11 designs, most often 10 kΩ (then 5.1 kΩ). Counted from the KiCad layouts of 11 open source designs using the PT4115.
Which microcontrollers do boards using the PT4115 use?
Most are built on ESP32 (5), ESP8266 (1) and Raspberry Pi (1).
How big is a typical board using the PT4115?
The median is 60.3 × 46.8 mm, and 88% are two-layer designs.
What is the most popular open source board using the PT4115?
By GitHub stars, CCFL2LED by mijuc, with 7 stars.
Can I simulate one of these boards using the PT4115 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.