Diy led spot routed

FaisalHussain95·esp32-espnow-led-spots·kicad/diy_led_spot/diy_led_spot_routed.kicad_pcb

Diy led spot routed PCB layout, top view — open source ESP32 board by FaisalHussain95

About the Diy led spot routed PCB

Diy led spot routed is an open source ESP32 PCB design by FaisalHussain95, published on GitHub. It is a 2-layer board measuring 55.5 × 55.5 mm, with 30 components from 21 distinct parts.

Its main chip is the ESP32-C3_SUPERMINI_SMD, from the ESP32 family. Other key parts include the DCDCStepDown, PT4115, MT3608 and 110kΩ. By type, the board carries 8 capacitors, 6 resistors, 5 ICs, 4 diodes, 2 inductors and 1 transistor.

It belongs with the iot & wireless designs in this gallery.

From the project

DIY 220VAC LED spot controller — ESP32-C3 + COB LED + PT4115 PWM dimming, NTC thermal protection, active fan cooling, ESP-NOW mesh. WiFi bridge for Home Assistant (MQTT).

Replacing 13 cheap 220V ceiling spots with custom COB LED units — dimmable, Home Assistant integrated, actively cooled, and wirelessly controlled over ESP-NOW.

I have 13 recessed spots installed across my ceiling. They were cheap 220V AC units with no heatsink — just a bare aluminium PCB glued to a plastic shell.

Opening one up tells the whole story: the driver circuit runs directly off mains voltage with no thermal management whatsoever.

Diy led spot routed, from the project README
From the project README

Main components on the Diy led spot routed

Diy led spot routed bill of materials (BOM)

30 components, 21 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
DCDCStepDown
U1
1
PT4115
U2
1
ESP32-C3_SUPERMINI_SMD
U3
1
MT3608
U4
1
110kΩ
U5
1
AO3400A
AO3400A_C347475
Q1
2
BX-XH2.54-2PZZ
-LED+1, FAN1
1
C19269965
0.33 1W
Rs1
1
MX1.25-2P
TEMP1
3
SS36
D1, D2, D3
1
SS36
1N4148W-7-F
D4
1
C167888
47uH 800mA
L1
1
SM3521-4R7MT
L2
1
C14858
100pF 50V
C1
2
C6119901
22uF 35V
C2, C4
1
C476766
100nF 50V
C3
2
100UF
100uF
C5, C8
2
100NF
100nF
C7, C9
4
C23186
5.1kΩ 100mW
R1, R2, R3, R7
1
RC0603FR-0747RL
R4
Show 1 more
QtyPartRefs
1
15kΩ
R6

Diy led spot routed design files

The KiCad project lives in the FaisalHussain95/esp32-espnow-led-spots repository on GitHub; these links point at the commit this page was built from.

Diy led spot routed: common questions

What microcontroller does the Diy led spot routed use?

The Diy led spot routed is built around the ESP32-C3_SUPERMINI_SMD, from the ESP32 family.

How big is the Diy led spot routed PCB?

The Diy led spot routed measures 55.5 × 55.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Diy led spot routed?

30 components, from 21 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Diy led spot routed design files?

From the FaisalHussain95/esp32-espnow-led-spots repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.

Can I use the Diy led spot routed design in my own project?

The repository has no license, so all rights stay with FaisalHussain95. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Diy led spot routed without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in esp32-espnow-led-spots

Similar boards