Cooler panel - placement (front: display, LEDs, keys)

faragamco-eng·Multiact·hardware/panel/out/kicad/cooler_panel.kicad_pcb

Cooler panel - placement (front: display, LEDs, keys) PCB layout, top view — open source ESP32 board by faragamco-eng

About the Cooler panel - placement (front: display, LEDs, keys) PCB

Cooler panel - placement (front: display, LEDs, keys) is an open source ESP32 PCB design by faragamco-eng, published on GitHub. It is a 2-layer board measuring 120 × 86 mm, with 92 components from 67 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the TI LMV331IDBVR (open drain), LM317DCY, Diodes AP63203WU (fixed 3.3 V) and ST USBLC6-2SC6. By type, the board carries 39 resistors, 18 capacitors, 7 transistors, 6 switches, 6 LEDs and 5 ICs.

It belongs with the iot & wireless and displays & leds designs in this gallery.

From the project

ساخت، مسیرکشی و بررسی: ./build.sh (حدود 5 تا 20 دقیقه؛ NOROUTE=1 ./build.sh فقط چیدمان). از ابزارها و کتابخانه‌های hardware/v2 استفاده می‌کند.

ساخت، مسیرکشی و بررسی: ./build.sh (حدود 5 تا 20 دقیقه؛ NOROUTE=1 ./build.sh فقط چیدمان). از ابزارها و کتابخانه‌های hardware/v2 استفاده می‌کند.

ابعاد برد: 120 × 86 mm، دولایه 1.6 mm؛ نمایشگر، LEDها و کلیدها در جلو. آنتن ماژول رو به لبه بالا و ناحیه زیر آنتن در هر دو لایه خالی از مس است.

قبل از سفارش ساخت، در KiCad/Altium یک بار نگاه کنید: مسیرهای ماشینی گوشه‌های زیادی دارند و جای بهینه‌سازی ظاهری هست (Cleanup / Optimize). جفت USB D+/D− بدون کنترل امپدانس است؛ برای USB 2.0 Full-Speed در این طول کوتاه مشکلی ندارد. سیلک‌اسکرین چند قطعه روی پد افتاده و باید جابه‌جا شود (فقط ظاهری).

Cooler panel - placement (front: display, LEDs, keys), from the project README
From the project README

Main components on the Cooler panel - placement (front: display, LEDs, keys)

TI LMV331IDBVR (open drain)LM317DCYDiodes AP63203WU (fixed 3.3 V)ESP32-S3-WROOM-1-N8ST USBLC6-2SC6

Cooler panel - placement (front: display, LEDs, keys) bill of materials (BOM)

92 components, 67 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
TI LMV331IDBVR (open drain)
LMV331
U1
1
LM317DCY
LM317 CC
U2
1
Diodes AP63203WU (fixed 3.3 V)
AP63203WU
U3
1
Espressif ESP32-S3-WROOM-1-N8 (NOT an R8 variant: IO35-37 are used)
ESP32-S3-WROOM-1-N8
U4
1
ST USBLC6-2SC6
USBLC6-2SC6
U5
1
BCX56-16 (SOT-89, 1 W)
BCX56
Q1
6
2N7002
Q2, Q3, Q4, Q5, Q6, Q7
1
BUS 2-WIRE
J1
1
GCT USB4105-GF-A
USB-C
J2
1
Diotec ABS10 (1000 V 0.8 A)
ABS10
BR1
1
magnetic buzzer 3 V, 2.7 kHz (e.g. CUI CMT-1203)
3V magnetic
BZ1
1
Kingbright CC56-12SURKWA (0.56 in, super-bright red, common cathode)
CC56-12SURKWA
DS1
1
Bourns MF-MSMF010
0.1A hold
F1
1
POWER
SW1
1
UP
SW2
1
DOWN
SW3
1
MODE
SW4
1
TIMER
SW5
1
BOOT
SW6
1
green
POWER
LED1
Show 47 more
QtyPartRefs
1
green
PUMP
LED2
1
green
FAN
LED3
1
green
TIMER
LED4
1
red
ALARM
LED5
1
blue
WIFI
LED6
1
SMBJ33CA (bidirectional)
SMBJ33CA
D1
1
1SMB5925BT3 (10 V 3 W)
10V 3W
D2
1
SS14
D3
1
1N4148W
D4
1
Bourns SRN6045TA-6R8M
6.8uH 1A
L1
1
100nF 50V
C1
1
1NF
1nF
C2
2
1NF
100nF
C3, C7
1
100nF
C4
1
low-ESR 105 C
1000uF 16V
C5
1
100NF
10uF 25V
C6
1
1NF
22uF 10V
C8
1
100PF
22uF 10V
C9
1
220PF
10uF
C10
1
1UF
100nF
C11
1
1uF
C12
4
10nF
C13, C14, C15, C16
1
100NF
10nF
C17
1
2.2NF
100nF
C18
1
470K
68k 1%
R1
1
470K
10k 1%
R2
1
470k
R3
1
4.02k 1%
R4
1
10k 1%
R5
7
10k
R6, R9, R33, R34, R35, R36, R37
2
1k
R7, R8
1
120R 1%
R10
1
470R 1W
R11
1
24R 1%
R12
1
10R
10k
R13
1
10K
10k
R14
2
5.1k
R15, R16
1
10R
22R
R17
1
22R
R18
6
150R
R20, R21, R22, R23, R24, R25
1
4.7K
150R
R26
1
22K
150R
R27
4
100K
100k
R28, R29, R30, R31
1
100k
R32
1
2.2K
100k
R38
1
4.7k
R39
1
100R
4.7k
R40

Cooler panel - placement (front: display, LEDs, keys) design files

The KiCad project lives in the faragamco-eng/Multiact repository on GitHub; these links point at the commit this page was built from.

Cooler panel - placement (front: display, LEDs, keys): common questions

What microcontroller does the Cooler panel - placement (front: display, LEDs, keys) use?

The Cooler panel - placement (front: display, LEDs, keys) is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.

How big is the Cooler panel - placement (front: display, LEDs, keys) PCB?

The Cooler panel - placement (front: display, LEDs, keys) measures 120 × 86 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Cooler panel - placement (front: display, LEDs, keys)?

92 components, from 67 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Cooler panel - placement (front: display, LEDs, keys) design files?

From the faragamco-eng/Multiact repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Cooler panel - placement (front: display, LEDs, keys) design in my own project?

The repository has no license, so all rights stay with faragamco-eng. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Cooler panel - placement (front: display, LEDs, keys) without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in Multiact

Similar boards