8 open source boards using the ST USBLC6-2SC6
Real designs built with the ST USBLC6-2SC6, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Nordic nRF
Deck-8
varaddorle007
92.8 × 76 mm87 parts4LMIT1ESP32
Battery monitor
ryanabraham1
100 × 80 mm72 parts2LNo license1Raspberry Pi
Rpi cm5-edge carrier
xmyoot
100 × 85 mm79 parts4LCC-BY-4.00ESP32
Flightline motor controller
markGilchrist
92 × 76 mm60 parts2LNo license0ESP32
Zemizdat
danindiana
50.8 × 22.9 mm55 parts4LNo license0NXP
LPC1114-LCD
MarceloSalazar
80 × 52 mm53 parts2LMIT0ESP32
ESP32 RGB LED CONTROLLER
theonlyakhil
20 × 50 mm43 parts2LNo license0RISC-V
DAC HPA
ooyang0325
120 × 100 mm470 parts4LNo license0
How designs wire the ST USBLC6-2SC6
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the ST USBLC6-2SC6 connects to, and the resistors, capacitors and other passives placed on it.
- Pin 2 is tied to GND on 8 of 8 designs.
- Pin 5 is tied to VBUS on 6 of 8 designs (a signal on 2).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| Pin 2 | Connected to: GND 100% | — |
| Pin 5 | Connected to: VBUS 75% · a signal 25% | — |
4 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Battery monitor by ryanabraham1, Deck-8 by varaddorle007, Zemizdat by danindiana and LPC1114-LCD by MarceloSalazar.
The ST USBLC6-2SC6 in open source designs
The gallery holds 8 open source boards using the ST USBLC6-2SC6 from 8 GitHub repositories; a typical one measures about 92.4 × 76 mm and carries around 66 components.
50% are two-layer designs, the rest use four layers or more, and 38% carry an open source license.
The most starred is Deck-8 by varaddorle007.
Parts used alongside the ST USBLC6-2SC6
Microcontrollers on boards using the ST USBLC6-2SC6
What boards using the ST USBLC6-2SC6 are built for
ST USBLC6-2SC6: common questions
Where can I find a ST USBLC6-2SC6 reference design?
Each of the 8 boards on this page is a real design using the ST USBLC6-2SC6. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the ST USBLC6-2SC6 pin 2 connected?
Pin 2 is tied to GND on 8 of 8 designs. Counted from the KiCad layouts of 8 open source designs using the ST USBLC6-2SC6.
How is the ST USBLC6-2SC6 pin 5 connected?
Pin 5 is tied to VBUS on 6 of 8 designs (a signal on 2). Counted from the KiCad layouts of 8 open source designs using the ST USBLC6-2SC6.
Which microcontrollers do boards using the ST USBLC6-2SC6 use?
Most are built on ESP32 (4), Nordic nRF (1), NXP (1) and Raspberry Pi (1).
How big is a typical board using the ST USBLC6-2SC6?
The median is 92.4 × 76 mm, and 50% are two-layer designs.
What is the most popular open source board using the ST USBLC6-2SC6?
By GitHub stars, Deck-8 by varaddorle007, with 1 stars.
Can I simulate one of these boards using the ST USBLC6-2SC6 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.