Multiplexer
GKeyMaster·eurorack_blocks·blocks/multiplexer/multiplexer.kicad_pcb
About the Multiplexer PCB
Multiplexer is an open source PCB design by GKeyMaster, published on GitHub under the CC-BY-SA-4.0 license. It is a 2-layer board measuring 22 × 19 mm, with 5 components from 5 distinct parts.
Other key parts include the 4051. By type, the board carries 2 connectors, 2 capacitors and 1 IC.
It belongs with the audio designs in this gallery.
From the project
This block allows to multiplex up to 8 pot or trim values into a single value. Its design is detailed here.
This block allows to multiplex up to 8 pot or trim values into a single value. Its design is detailed here.
The number of actual Analog GPIOs on an MCU is always very limited, and one can quickly have more controls and CVs on their panel than the number of available Analog GPIOs.
Multiplexing multiple signals to one signal allows to overcome this problem, at the expense of a slower reading rate. Therefore it is suited for slowly varying signals such as the ones delivered by a potentiometer.

Main components on the Multiplexer
Multiplexer bill of materials (BOM)
5 components, 5 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 4051 | TSSOP-16_4.4x5mm_P0.65mm | U1 |
| 1 | BOTTOM | PinHeader_1x08_P2.54mm_Vertical | J2 |
| 1 | TOP | PinHeader_1x08_P2.54mm_Vertical | J3 |
| 1 | 1n | C_0603_1608Metric | C1 |
| 1 | 100n | C_0603_1608Metric | C2 |
Multiplexer design files
The KiCad project lives in the GKeyMaster/eurorack_blocks repository on GitHub; these links point at the commit this page was built from.
Multiplexer: common questions
How big is the Multiplexer PCB?
The Multiplexer measures 22 × 19 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Multiplexer?
5 components, from 5 distinct parts. The full bill of materials is listed on this page.
Where can I download the Multiplexer design files?
From the GKeyMaster/eurorack_blocks repository on GitHub, which has the KiCad layout; the links under Design files point to each one.
Can I use the Multiplexer design in my own project?
Yes, under the terms of its CC-BY-SA-4.0 license, which GKeyMaster chose for the repository.
More boards in eurorack_blocks
Kivu12
GKeyMaster
59.6 × 109.5 mm135 parts2LCC-BY-SA-4.00Panel daisy
GKeyMaster
148 × 84.5 mm20 parts2LCC-BY-SA-4.00Audio out daisy
GKeyMaster
25 × 19 mm13 parts2LCC-BY-SA-4.00Cv in
GKeyMaster
25 × 19 mm13 parts2LCC-BY-SA-4.00Audio in daisy
GKeyMaster
25 × 19 mm13 parts2LCC-BY-SA-4.00Power bus
GKeyMaster
37 × 21.5 mm9 parts2LCC-BY-SA-4.00Regulator daisy
GKeyMaster
20 × 19 mm8 parts2LCC-BY-SA-4.00Gate in
GKeyMaster
20 × 19 mm8 parts2LCC-BY-SA-4.00Slider
GKeyMaster
17 × 35.5 mm7 parts2LCC-BY-SA-4.00Gate out
GKeyMaster
20 × 19 mm7 parts2LCC-BY-SA-4.00Trim
GKeyMaster
17 × 19 mm5 parts2LCC-BY-SA-4.00
Similar boards
KLOR
GEIGEIGEIST
160.2 × 118.3 mm79 parts2LGPL-3.01.2kButtonsLEDs
shanteacontrols
390 × 37 mm82 parts2LApache-2.0956USB
shanteacontrols
52 × 12.6 mm6 parts2LApache-2.0956Pots
shanteacontrols
390 × 93 mm75 parts2LApache-2.0956PicoGUS Hand386
polpo
29.2 × 75.2 mm43 parts4LGPL-2.0800Snark barker
schlae
231.1 × 106.7 mm193 parts2LNo license687