Tiago robotiq adapter
hardware-designs-iai·tiago_robotiq_adapter·pcbs/TIAGO_gripper.kicad_pcb
About the Tiago robotiq adapter PCB
Tiago robotiq adapter is an open source ESP32 PCB design by hardware-designs-iai, published on GitHub. It is a 4-layer board measuring 62 × 60 mm, with 56 components from 39 distinct parts.
Its main chip is the ESP32-C3-MINI-1, from the ESP32 family. Other key parts include the SP3485EN-L, RY8411, SRV05-4 and TPS54360BDDAR. By type, the board carries 19 resistors, 16 capacitors, 5 ICs, 5 connectors, 5 diodes and 3 inductors.
It belongs with the robotics & motion designs in this gallery.
From the project
PCB designs to connect a Robotiq gripper to the TIAGo.
Main components on the Tiago robotiq adapter
Tiago robotiq adapter bill of materials (BOM)
56 components, 39 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-C3-MINI-1 | ESP32-S3-MINI-1 | U1 |
| 1 | SP3485EN-L SP3485EN-L/TR | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | RY8411 | SOT-23-6 | U4 |
| 1 | SRV05-4 | SOT-23-6 | U5 |
| 1 | TPS54360BDDAR | TI_SO-PowerPAD-8_ThermalVias | U6 |
| 1 | USB_C_RECEPTACLE_USB2.0 USB_C_Receptacle_USB2.0 | USB_C_Receptacle_G-Switch_GT-USB-7010ASV | J1 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | PinHeader_1x02_P1.00mm_Vertical | J2 |
| 1 | S3B-XH-ALFSN | CONN_S3B-XH-ALFSN_JST | J3 |
| 1 | CONN_02X05_COUNTER_CLOCKWISE Conn_02x05_Counter_Clockwise | PinHeader_2x05_P2.54mm_Vertical | J4 |
| 1 | CONN_01X02_PIN Conn_01x02_Pin | PinHeader_2x01_P1.27mm_Vertical_SMD | J5 |
| 2 | SW_Push | SW_Push_SPST_NO_Alps_SKRK | Boot1, Reset1 |
| 1 | CONN_01X03_PIN Conn_01x03_Pin | PinHeader_1x03_P1.00mm_Vertical | LED1 |
| 2 | LED | LED_0603_1608Metric | D1, D2 |
| 1 | SS510 | D_SMB | D3 |
| 2 | C8598 B5819W SL | D_SOD-123 | D4, D5 |
| 1 | C1002 FerriteBead_Small | L_0603_1608Metric | FB1 |
| 1 | 22UH/2.5A 22uH/2.5A | L_Bourns_SRN8040TA | L1 |
| 1 | 4.7UH 4.7uH | L_Changjiang_FNR4030S | L2 |
| 1 | 22UF/50V 22uF/50V | C_0402_1005Metric | C1 |
| 2 | 22UF/50V 22uF/50V | C_0603_1608Metric | C2, C14 |
Show 19 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 4 | 0.1UF 0.1uF | C_0402_1005Metric | C3, C4, C5, C15 |
| 1 | 3.3NF 3.3nF | C_0603_1608Metric | C6 |
| 1 | 6.8NF 6.8nF | C_0603_1608Metric | C7 |
| 1 | 82UF 82uF | CP_Elec_6.3x3 | C8 |
| 3 | 10UF/50V 10uF/50V | C_0805_2012Metric | C9, C11, C13 |
| 1 | 100NF 100nF | C_0402_1005Metric | C10 |
| 1 | 47UF/10V 47uF/10V | CP_EIA-3528-21_Kemet-B | C12 |
| 1 | 2.2UF 2.2uF | C_0805_2012Metric | C16 |
| 4 | 100K | R_0402_1005Metric | R1, R8, R9, R14 |
| 1 | 133K | R_0402_1005Metric | R2 |
| 1 | 44.2K | R_0402_1005Metric | R3 |
| 3 | 2.2K | R_0402_1005Metric | R4, R5, R16 |
| 1 | 348K | R_0402_1005Metric | R6 |
| 1 | 12K | R_0402_1005Metric | R7 |
| 2 | 5.1K | R_0402_1005Metric | R10, R11 |
| 1 | 56.2K | R_0402_1005Metric | R12 |
| 1 | 120R | R_0402_1005Metric | R13 |
| 2 | 10K | R_0402_1005Metric | R15, R19 |
| 2 | C17168 0R | R_0402_1005Metric | R17, R18 |
Tiago robotiq adapter design files
The KiCad project lives in the hardware-designs-iai/tiago_robotiq_adapter repository on GitHub; these links point at the commit this page was built from.
Tiago robotiq adapter: common questions
What microcontroller does the Tiago robotiq adapter use?
The Tiago robotiq adapter is built around the ESP32-C3-MINI-1, from the ESP32 family.
How big is the Tiago robotiq adapter PCB?
The Tiago robotiq adapter measures 62 × 60 mm, has 4 copper layers and is 1.565 mm thick.
How many components are on the Tiago robotiq adapter?
56 components, from 39 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Tiago robotiq adapter design files?
From the hardware-designs-iai/tiago_robotiq_adapter repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Tiago robotiq adapter design in my own project?
The repository has no license, so all rights stay with hardware-designs-iai. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Tiago robotiq adapter without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8k