T1 panel
hwkim3330·sfp-auto-ethernet·hw/t1/panel/t1_panel.kicad_pcb
About the T1 panel PCB
T1 panel is an open source STM32 PCB design by hwkim3330, published on GitHub. It is a 4-layer board measuring 71.5 × 81 mm, with 59 components from 33 distinct parts.
Its main chip is the STM32G031F6P6, from the STM32 family. Other key parts include the DP83TG720S-Q1 (or DP83TC812S-Q1), TPS62822DLC and TPS22918DBVR. By type, the board carries 35 capacitors, 9 resistors, 7 inductors, 4 ICs, 2 connectors and 1 crystal.
From the project
SFP modules that speak SGMII to the host and 100/1000BASE-T1, 1000BASE-T or 10BASE-T1S to the world (KiCad)
Schematic, PCB (4 layers, routed), fab outputs and firmware are all in place. Order files are in jlc/, and the order sheet is ORDER.md. The only open choice is which PHY to use (TG720 stock problem).
- PHY: DP83TG720S-Q1 (1000BASE-T1). - The DP83TC812S-Q1 (100BASE-T1) fits the same footprint. For the 100 Mb loadout, leave FB3 unfitted (the 1.0 V buck → pins 9/21 ferrite); the TC812 regulates pin 21 itself. - The straps are all left at their defaults: SGMII, PHY address 0, autonomous, slave. The MCU must still set the SGMII polarity bits at start-up (see below). - SGMII: SFP TD/RD → 100 nF AC…

Main components on the T1 panel
T1 panel bill of materials (BOM)
59 components, 33 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | DP83TG720S-Q1 (or DP83TC812S-Q1) | QFN-36-1EP_6x6mm_P0.5mm_EP3.7x3.7mm_ThermalVias | U1 |
| 1 | STM32G031F6P6 | TSSOP-20_4.4x6.5mm_P0.65mm | U2 |
| 1 | TPS62822DLC | Texas_VSON-HR-8_1.5x2mm_P0.5mm | U3 |
| 1 | TPS22918DBVR | SOT-23-6 | U4 |
| 1 | 25MHz CL8pF 2016 | Crystal_SMD_2016-4Pin_2.0x1.6mm | Y1 |
| 1 | SFP edge (INF-8074i) | SFP_Module_Edge | J1 |
| 1 | Rosenberger E6S20A-40MT5-Z (H-MTD, coding Z) | Rosenberger_HMTD_E6S20A_1P_RA | J2 |
| 1 | green | LED_0402_1005Metric | D1 |
| 3 | BLM18KG601SH1 | L_0603_1608Metric | FB1, FB2, FB4 |
| 1 | BLM18KG601SH1 (DNP for DP83TC812) | L_0603_1608Metric | FB3 |
| 1 | BLM18HE102SN1 | L_0603_1608Metric | FB5 |
| 1 | 470nH DFE201610E-R47M | L_Murata_DFE201610P | L1 |
| 1 | DLW32MH101XT2 | L_CommonMode_3225 | L2 |
| 2 | 1uF | C_0402_1005Metric | C1, C31 |
| 3 | 100nF | C_0402_1005Metric | C2, C30, C32 |
| 10 | 100nF | C_0201_0603Metric | C3, C4, C5, C6, C8, C10, C12, C14 +2 |
| 5 | 10nF | C_0201_0603Metric | C7, C11, C13, C16, C19 |
| 4 | 2.2uF | C_0402_1005Metric | C9, C15, C18, C21 |
| 2 | 12pF | C_0201_0603Metric | C24, C25 |
| 1 | 4.7uF | C_0402_1005Metric | C26 |
Show 13 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 3 | 10uF | C_0603_1608Metric | C27, C28, C37 |
| 1 | 120pF | C_0201_0603Metric | C29 |
| 2 | 100nF 100V | C_0402_1005Metric | C33, C34 |
| 1 | 4.7nF | C_0402_1005Metric | C35 |
| 1 | 2.2nF | C_0402_1005Metric | C36 |
| 1 | 2.2k | R_0201_0603Metric | R1 |
| 1 | 1k | R_0402_1005Metric | R2 |
| 1 | 66.5k 1% | R_0201_0603Metric | R3 |
| 1 | 100k 1% | R_0201_0603Metric | R4 |
| 1 | 10k | R_0402_1005Metric | R5 |
| 2 | 1k 1% 0.75W | R_2010_5025Metric | R6, R7 |
| 1 | 100k | R_0402_1005Metric | R8 |
| 1 | 0 | R_0201_0603Metric | R9 |
T1 panel design files
The KiCad project lives in the hwkim3330/sfp-auto-ethernet repository on GitHub; these links point at the commit this page was built from.
T1 panel: common questions
What microcontroller does the T1 panel use?
The T1 panel is built around the STM32G031F6P6, from the STM32 family.
How big is the T1 panel PCB?
The T1 panel measures 71.5 × 81 mm, has 4 copper layers and is 1 mm thick.
How many components are on the T1 panel?
59 components, from 33 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the T1 panel design files?
From the hwkim3330/sfp-auto-ethernet repository on GitHub, which has the KiCad layout and the BOM; the links under Design files point to each one.
Can I use the T1 panel design in my own project?
The repository has no license, so all rights stay with hwkim3330. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the T1 panel without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.
More boards in sfp-auto-ethernet
Similar boards
STM32
LumenPnP Motherboard
opulo-inc
149 × 95 mm296 parts4LCC-BY-SA-4.03.7kSTM32
Type g
google
169 × 30 mm24 parts2LApache-2.02.9kSTM32
Main panel
google
234 × 84 mm26 parts4LApache-2.02.9kSTM32
Base
google
52.3 × 52.3 mm36 parts2LApache-2.02.9kSTM32
Type a
google
150 × 30 mm14 parts2LApache-2.02.9kSTM32
Type c
google
188 × 30 mm17 parts2LApache-2.02.9k