8 open source boards using the TPS62822DLC
Real designs built with the TPS62822DLC, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
AVR/Arduino
Project-Okapi
NorthernWidget
64.8 × 135 mm251 parts2LCC-BY-SA-4.08ESP32
ESP
MurilloHorvath
152.2 × 93.3 mm72 parts2LMIT1STM32
Strojni posuv
HolTyc
227 × 80 mm121 parts2LNo license0FPGA
FPGBA
teejaytiger
78.8 × 40 mm65 parts2LNo license0STM32
T1s panel
hwkim3330
70 × 81 mm83 parts6LNo license0FPGA
Mainboard
teejaytiger
78.8 × 40 mm55 parts4LNo license0STM32
Rj45 panel
hwkim3330
71.4 × 107 mm65 parts6LNo license0STM32
T1 panel
hwkim3330
71.5 × 81 mm59 parts4LNo license0
How designs wire the TPS62822DLC
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the TPS62822DLC connects to, and the resistors, capacitors and other passives placed on it.
- The NC_4 pin is left unconnected on 5 of 5 designs.
- The SW_6 pin has a inductor on 4 of 5 designs, most often 2.2 µH (then 1 µH).
- The PG_8 pin is left unconnected on 4 of 5 designs.
- The FB_2 pin has a resistor to GND on 3 of 5 designs, most often 180 kΩ (then 10 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| FB_2pin 2 | Connected to: Signal 80% · 3.3V 20% |
|
| AGND_3pin 3 | Connected to: GND 80% · a signal 20% | — |
| NC_4pin 4 | Connected to: Not connected 100% | — |
| PGND_5pin 5 | Connected to: GND 80% · a signal 20% | — |
| SW_6pin 6 | Connected to: Signal 80% · not connected 20% |
|
| VIN_7pin 7 | Connected to: 5V 60% · a signal 40% |
|
| PG_8pin 8 | Connected to: Not connected 80% · 3.3V 20% | — |
1 more pin varies from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Project-Okapi by NorthernWidget, ESP by MurilloHorvath, Strojni posuv by HolTyc and Rj45 panel by hwkim3330.
The TPS62822DLC in open source designs
The gallery holds 8 open source boards using the TPS62822DLC from 5 GitHub repositories; a typical one measures about 75.1 × 81 mm and carries around 69 components.
50% are two-layer designs, the rest use four layers or more, and 25% carry an open source license.
The most starred is Project-Okapi by NorthernWidget.
Parts used alongside the TPS62822DLC
Microcontrollers on boards using the TPS62822DLC
What boards using the TPS62822DLC are built for
TPS62822DLC: common questions
Where can I find a TPS62822DLC reference design?
Each of the 8 boards on this page is a real design using the TPS62822DLC. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TPS62822DLC NC_4 pin connected?
The NC_4 pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS62822DLC.
How is the TPS62822DLC SW_6 pin connected?
The SW_6 pin has a inductor on 4 of 5 designs, most often 2.2 µH (then 1 µH). Counted from the KiCad layouts of 5 open source designs using the TPS62822DLC.
How is the TPS62822DLC PG_8 pin connected?
The PG_8 pin is left unconnected on 4 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the TPS62822DLC.
Which microcontrollers do boards using the TPS62822DLC use?
Most are built on STM32 (4), FPGA (2), AVR/Arduino (1) and ESP32 (1).
How big is a typical board using the TPS62822DLC?
The median is 75.1 × 81 mm, and 50% are two-layer designs.
What is the most popular open source board using the TPS62822DLC?
By GitHub stars, Project-Okapi by NorthernWidget, with 8 stars.
Can I simulate one of these boards using the TPS62822DLC before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.