T1s

hwkim3330·sfp-auto-ethernet·hw/t1s/t1s.kicad_pcb

T1s PCB layout, top view — open source STM32 board by hwkim3330

About the T1s PCB

T1s is an open source STM32 PCB design by hwkim3330, published on GitHub. It is a 6-layer board measuring 58.4 × 11.8 mm, with 83 components from 32 distinct parts.

Its main chip is the STM32G031F6P6, from the STM32 family. Other key parts include the GW5AT-LV15MG132C1/I0, GD25Q128EWIGR, TPS62822DLCR, TPS22918DBVR and LAN8670C2-E/LMX. By type, the board carries 40 capacitors, 25 resistors, 8 ICs, 6 inductors, 2 crystals and 2 connectors.

From the project

SFP modules that speak SGMII to the host and 100/1000BASE-T1, 1000BASE-T or 10BASE-T1S to the world (KiCad)

No 10BASE-T1S PHY speaks SGMII (they are all MII/RMII or SPI MAC-PHYs; see ../../docs/PARTS.md). So an FPGA sits between the two: - the host's SGMII on a hard transceiver lane; - our own PCS, ×100 rate adaptation, frame FIFOs and half-duplex MAC in fabric (gw/); - MII to a Microchip LAN8670.

This is the board with the most unverified pieces. See What is not verified.

T1s, from the project README
From the project README

Main components on the T1s

GW5AT-LV15MG132C1/I0GD25Q128EWIGRTPS62822DLCRTPS22918DBVRLAN8670C2-E/LMXTLV75518PDBVRTLV75512PDBVRSTM32G031F6P6

T1s bill of materials (BOM)

83 components, 32 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
GW5AT-LV15MG132C1/I0
U1
1
GD25Q128EWIGR
U2
1
TPS62822DLCR
TPS62822DLC
U3
1
TPS22918DBVR
U4
1
LAN8670C2-E/LMX
U5
1
TLV75518PDBVR
U6
1
TLV75512PDBVR
U7
1
STM32G031F6P6
U8
1
OB2EL89CLIB112YLC-125M
X1
1
25MHz CL12pF 2016
Y1
1
SFP edge (INF-8074i)
J1
1
S2B-PH-K-S(LF)(SN)
S2B-PH-K-S
J2
4
BLM18KG601SH1
FB1, FB2, FB3, FB4
1
DFE201610E-1R0M
1uH DFE201610E-1R0M
L1
1
ACT1210E-241-2P-TL00
ACT1210E-241-2P
L2
5
1uF
C1, C15, C16, C17, C44
3
100nF
C2, C43, C45
19
100nF
C3, C4, C5, C6, C7, C8, C9, C32 +11
2
4.7uF
C11, C18
3
10uF
C12, C13, C60
Show 12 more
QtyPartRefs
1
120pF
C14
2
18pF
C30, C31
1
2.2nF
C36
1
10uF
C37
3
100nF 100V
C40, C41, C42
7
4.7k
R1, R3, R4, R5, R6, R7, R26
1
57.6k 1%
R8
1
100k 1%
R9
12
10k
R10, R11, R12, R13, R14, R15, R16, R17 +4
1
12.4k 1%
R21
2
CRCW120649R9FKEAHP
49.9 1% 0.75W
R22, R23
1
100k
R24

T1s design files

The KiCad project lives in the hwkim3330/sfp-auto-ethernet repository on GitHub; these links point at the commit this page was built from.

T1s: common questions

What microcontroller does the T1s use?

The T1s is built around the STM32G031F6P6, from the STM32 family.

How big is the T1s PCB?

The T1s measures 58.4 × 11.8 mm, has 6 copper layers and is 1 mm thick.

How many components are on the T1s?

83 components, from 32 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the T1s design files?

From the hwkim3330/sfp-auto-ethernet repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the T1s design in my own project?

The repository has no license, so all rights stay with hwkim3330. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the T1s without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug STM32 firmware against it before you order a PCB.

More boards in sfp-auto-ethernet

Similar boards