HardLabs

Linear-CCD-camera-V1

Jed0vcela·Linear-CCD-camera-V1

Linear-CCD-camera-V1 PCB layout, top view — open source Raspberry Pi board by Jed0vcela

About the Linear-CCD-camera-V1 PCB

Linear-CCD-camera-V1 is an open source Raspberry Pi PCB design by Jed0vcela, published on GitHub. It is a 2-layer board measuring 95.5 × 90.9 mm, with 98 components from 36 distinct parts.

Its main chip is the RaspberryPi_Pico_W, from the Raspberry Pi family. Other key parts include the TLV61048DBVR, 74HC14, MCP73832-2-OT, LM4040DBZ-3 and AMS1117-5.0. By type, the board carries 35 resistors, 28 capacitors, 9 ICs, 4 diodes, 3 modules and 3 transistors.

It belongs with the sensors designs in this gallery.

From the project

Prototype of "scanning" camera using linar CCD sensor ILX555K

Main components on the Linear-CCD-camera-V1

TLV61048DBVR74HC14MCP73832-2-OTLM4040DBZ-3AMS1117-5.0TLV9064RaspberryPi_Pico_WPOLOLU_BREAKOUT_A4988

Linear-CCD-camera-V1 bill of materials (BOM)

98 components, 36 distinct parts — part numbers from the project's BOM.

QtyPartRefs
2
TLV61048DBVR
IC1, IC2
1
~
U1
2
74HC14
U4, U8
1
MCP73832-2-OT
U5
1
LM4040DBZ-3
U6
1
AMS1117-5.0
U7
1
TLV9064
U9
1
RaspberryPi_Pico_W
A1
2
POLOLU_BREAKOUT_A4988
Pololu_Breakout_A4988
A2, A3
3
BC817
Q1, Q2, Q3
1
MSD-1-A
J1
2
FFC2B35-18-G
J5, J6
3
10K
RV1, RV2, RV3
1
SLW-135987-5A-N-D
S2
2
Conn_01x02_Pin
batt1, end_sw1
2
Conn_01x04_Pin
stepper1, stepper2
1
OLED-128O064D
DS1
1
charge
charge1
4
D_Schottky
D1, D2, D3, D4
1
FerriteBead
FB1
Show 16 more
QtyPartRefs
2
4U7
4u7
L1, L3
1
100N
100n
C3
2
C_Polarized
C4, C24
16
4U7
4u7
C5, C6, C7, C8, C9, C11, C12, C13 +8
2
NC
C10, C29
6
1u
C16, C19, C21, C22, C25, C26
1
10U
10u
C20
2
18K
18k
R1, R37
3
2k
R2, R14, R38
4
2
R3, R4, R5, R6
7
100
R7, R8, R9, R10, R11, R12, R13
1
2k
R15
2
NC
R16, R33
12
5K1
5k1
R17, R18, R19, R20, R21, R22, R23, R24 +4
1
470K
470k
R29
3
NC
R30, R31, R32

Linear-CCD-camera-V1 design files

The KiCad project lives in the Jed0vcela/Linear-CCD-camera-V1 repository on GitHub; these links point at the commit this page was built from.

Linear-CCD-camera-V1: common questions

What microcontroller does the Linear-CCD-camera-V1 use?

The Linear-CCD-camera-V1 is built around the RaspberryPi_Pico_W, from the Raspberry Pi family.

How big is the Linear-CCD-camera-V1 PCB?

The Linear-CCD-camera-V1 measures 95.5 × 90.9 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Linear-CCD-camera-V1?

98 components, from 36 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Linear-CCD-camera-V1 design files?

From the Jed0vcela/Linear-CCD-camera-V1 repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Linear-CCD-camera-V1 design in my own project?

The repository has no license, so all rights stay with Jed0vcela. Use it as a reference, and ask the author before reusing the design.

Can I test firmware for the Linear-CCD-camera-V1 without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug Raspberry Pi firmware against it before you order a PCB.

Similar boards