9 open source boards using the TLV61048DBVR
Real designs built with the TLV61048DBVR, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
DCDCv9-3
Rootthecause
85.6 × 54 mm186 parts4LCERN-OHL-W-2.0146ESP32
OBSPro
FabianSchwartau
64 × 77 mm117 parts4LLGPL-2.13STM32
PM Controller
ZeshuLiu
90 × 61.5 mm118 parts4LCustom license1Raspberry Pi
Linear-CCD-camera-V1
Jed0vcela
95.5 × 90.9 mm98 parts2LNo license1STM32
Audio-DSP-Guitar-Pedal
Jonkaphi
136 × 186 mm260 parts4LNo license0STM32
KiCAD Test
shayesMEL
170 × 120 mm92 parts2LNo license0STM32
Haptic linear slider
jdelgranchio
130.5 × 46 mm62 parts2LNo license0ESP32
ESP+Power Only
aaronluebbert
55.2 × 137.2 mm35 parts2LNo license1MotroDrive
ZeshuLiu
33 × 48 mm16 parts2LCustom license1
How designs wire the TLV61048DBVR
Read from the KiCad layouts of 8 open source designs, one per repository: what each pin of the TLV61048DBVR connects to, and the resistors, capacitors and other passives placed on it.
- The SW pin has a inductor on 8 of 8 designs, most often 4.7 µH (then 10 µH).
- The FB pin has a resistor to GND on 8 of 8 designs, most often 33 kΩ (then 100 kΩ).
- The VIN pin has a decoupling capacitor on 8 of 8 designs, most often 1 µF (then 4.7 µF).
- The VIN pin has a inductor on 6 of 8 designs, most often 4.7 µH (then 10 µH).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| SWpin 1 | Connected to: Signal 100% |
|
| GNDpin 2 | Connected to: GND 100% | — |
| FBpin 3 | Connected to: Signal 100% |
|
| ENpin 4 | Connected to: BATT 63% · a signal 38% |
|
| VINpin 5 | Connected to: BATT 75% · a signal 25% |
|
| FREQpin 6 | Connected to: Not connected 63% · GND 25% | — |
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include DCDCv9-3 by Rootthecause, OBSPro by FabianSchwartau, ESP+Power Only by aaronluebbert and Linear-CCD-camera-V1 by Jed0vcela.
The TLV61048DBVR in open source designs
The gallery holds 9 open source boards using the TLV61048DBVR from 8 GitHub repositories; a typical one measures about 90 × 77 mm and carries around 98 components.
56% are two-layer designs, the rest use four layers or more, and 22% carry an open source license.
The most starred is DCDCv9-3 by Rootthecause.
Parts used alongside the TLV61048DBVR
Microcontrollers on boards using the TLV61048DBVR
What boards using the TLV61048DBVR are built for
TLV61048DBVR: common questions
Where can I find a TLV61048DBVR reference design?
Each of the 9 boards on this page is a real design using the TLV61048DBVR. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the TLV61048DBVR SW pin connected?
The SW pin has a inductor on 8 of 8 designs, most often 4.7 µH (then 10 µH). Counted from the KiCad layouts of 8 open source designs using the TLV61048DBVR.
What resistor goes on the TLV61048DBVR FB pin?
The FB pin has a resistor to GND on 8 of 8 designs, most often 33 kΩ (then 100 kΩ). Counted from the KiCad layouts of 8 open source designs using the TLV61048DBVR.
What decoupling capacitors do designs use on the TLV61048DBVR VIN pin?
The VIN pin has a decoupling capacitor on 8 of 8 designs, most often 1 µF (then 4.7 µF). Counted from the KiCad layouts of 8 open source designs using the TLV61048DBVR.
Which microcontrollers do boards using the TLV61048DBVR use?
Most are built on STM32 (4), ESP32 (2) and Raspberry Pi (1).
How big is a typical board using the TLV61048DBVR?
The median is 90 × 77 mm, and 56% are two-layer designs.
What is the most popular open source board using the TLV61048DBVR?
By GitHub stars, DCDCv9-3 by Rootthecause, with 146 stars.
Can I simulate one of these boards using the TLV61048DBVR before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.