Motion tracking electric watergun

jonathanrandall·motion_tracking_electric_watergun·kicad_stuff/watergun_pcb.kicad_pcb

Motion tracking electric watergun PCB layout, top view — open source ESP32 board by jonathanrandall

About the Motion tracking electric watergun PCB

Motion tracking electric watergun is an open source ESP32 PCB design by jonathanrandall, published on GitHub under the MIT license. It is a 2-layer board measuring 142.8 × 99.5 mm, with 76 components from 31 distinct parts.

Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the USBLC6-2SC6 and AP63203WU-7. By type, the board carries 26 resistors, 14 capacitors, 10 connectors, 8 switches, 5 diodes and 3 ICs.

It belongs with the robotics & motion, iot & wireless and displays & leds designs in this gallery.

From the project

motion tracking electric watergun

An ESP32-based automatic water gun that tracks motion using an array of ultrasonic sensors and can be remote-controlled via a wireless joystick. Built around a custom KiCad PCB with a 3D-printed enclosure.

The gun mounts on a pan/tilt servo gimbal. Five ultrasonic sensors span the field of view (far-left, left, center, right, far-right). When a target enters range, the gun snaps its pan servo to the closest detected sensor — blending between adjacent sensors for smoother interpolation — and begins auto-firing the water pump in timed on/off pulses. A wireless joystick remote (ESP32 DEVKIT V1)…

Main components on the Motion tracking electric watergun

Motion tracking electric watergun bill of materials (BOM)

76 components, 31 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1
U1
1
USBLC6-2SC6
U2
1
AP63203WU-7
U3
1
C20917
Q_NMOS_GDS
Q2
1
C20917
Q_NMOS_GSD
Q3
1
USB_C_RECEPTACLE_USB2.0_16P
USB_C_Receptacle_USB2.0_16P
J1
1
Conn_01x09
J2
1
Conn_01x02
J5
5
Conn_01x04
J7, J8, J9, J10, J11
2
IN OUT
J16, J17
2
Conn_02x04_Top_Bottom
3V3_rail1, V5_rail1
1
Conn_02x04_Odd_Even
I2C1
3
330R
R_LED1, R_LED2, R_LED3
1
C318884
SW_Boot
SW1
1
C318884
SW_RESET
SW2
3
BUTTON_1
button_1
SW3, SW5, SW7
3
BUTTON_2
button_2
SW4, SW6, SW8
1
Conn_02x04_Odd_Even
Servo_in1
2
C2480
D_Schottky
D4, D5
1
C2286
RED LED
D6
Show 11 more
QtyPartRefs
1
C2296
Orange LED
D7
1
C2297
GREEN LED
D8
1
4.7UH
4.7uH
L1
2
22UF
22uF
C1, C2
10
100NF
100nF
C5, C19, C21, C22, C23, C24, C25, C26 +2
2
10UF
10uF
C17, C20
2
5.1K
R1, R2
2
27R
R3, R4
15
10K
R8, R9, R10, R11, R12, R13, R14, R15 +7
2
100R
R20, R22
5
20K
R25, R26, R27, R28, R29

Motion tracking electric watergun design files

The KiCad project lives in the jonathanrandall/motion_tracking_electric_watergun repository on GitHub; these links point at the commit this page was built from.

Motion tracking electric watergun: common questions

What microcontroller does the Motion tracking electric watergun use?

The Motion tracking electric watergun is built around the ESP32-S3-WROOM-1, from the ESP32 family.

How big is the Motion tracking electric watergun PCB?

The Motion tracking electric watergun measures 142.8 × 99.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Motion tracking electric watergun?

76 components, from 31 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Motion tracking electric watergun design files?

From the jonathanrandall/motion_tracking_electric_watergun repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Motion tracking electric watergun design in my own project?

Yes, under the terms of its MIT license, which jonathanrandall chose for the repository.

Can I test firmware for the Motion tracking electric watergun without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

Similar boards