Esp32 PD
Joshm196·esp32_PD

About the Esp32 PD PCB
Esp32 PD is an open source ESP32 PCB design by Joshm196, published on GitHub. It is a board, with 58 components from 27 distinct parts.
Its main chip is the ESP32-S3-WROOM-1, from the ESP32 family. Other key parts include the LM5148RGYR, AP63203WU, FDS6975 and CYPD3177-24LQ. By type, the board carries 35 capacitors, 13 resistors, 6 ICs, 2 switches, 1 connector and 1 inductor.
It belongs with the power & battery designs in this gallery.
From the project
ESP32 Power Delivery board for wled
ESP32 Power Delivery (PD) board for WLED Not finished
This is a safety feature to aviod forgetting to change wled max load the pulling more than supplied. someone who knows what they are doing could change this with the sink's i2c pins and do backflips or whatever idc its not my house
100W is plenty enough. (I could not find a PD 3.1 250W sink readily in stock and blah blah blah—100W simplifies everything.)
Main components on the Esp32 PD
Esp32 PD bill of materials (BOM)
58 components, 27 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | ESP32-S3-WROOM-1 | ESP32-S3-WROOM-1 | U1 |
| 2 | LM5148RGYR | QFN50P550X350X100-25N | U2, U6 |
| 1 | AP63203WU | TSOT-23-6 | U3 |
| 1 | FDS6975 | SOIC127P600X175-8N | U4 |
| 1 | CYPD3177-24LQ | QFN-24-1EP_4x4mm_P0.5mm_EP2.75x2.75mm | U5 |
| 1 | USB_C_Receptacle_USB2.0_14P | J1 | |
| 1 | reset | SW1 | |
| 1 | BOOT | SW2 | |
| 1 | 3.9u | L1 | |
| 3 | 0.1u | C1, C3, C4 | |
| 2 | 10u | C2, C5 | |
| 17 | 100n | C6, C8, C11, C14, C15, C16, C17, C18 +9 | |
| 4 | 1u | C7, C12, C20, C21 | |
| 2 | 22u | C9, C10 | |
| 1 | 4u | C13 | |
| 4 | 4u7 | C26, C27, C32, C33 | |
| 2 | ? | C34, C35 | |
| 1 | 10k | R1 | |
| 2 | 55k | R2, R10 | |
| 1 | 54k9 | R3 |
Show 7 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 2 | 2k2 | R4, R6 | |
| 1 | 130 k | R5 | |
| 2 | 56k2 | R7, R9 | |
| 1 | 20k | R8 | |
| 1 | 90k9 | R11 | |
| 1 | 24k9 | R12 | |
| 1 | ? | R13 |
Esp32 PD design files
The KiCad project lives in the Joshm196/esp32_PD repository on GitHub; these links point at the commit this page was built from.
- SchematicPD_esp32Cad.kicad_sch
Esp32 PD: common questions
What microcontroller does the Esp32 PD use?
The Esp32 PD is built around the ESP32-S3-WROOM-1, from the ESP32 family.
How many components are on the Esp32 PD?
58 components, from 27 distinct parts. The full bill of materials is listed on this page.
Where can I download the Esp32 PD design files?
From the Joshm196/esp32_PD repository on GitHub, which has the schematic; the links under Design files point to each one.
Can I use the Esp32 PD design in my own project?
The repository has no license, so all rights stay with Joshm196. Use it as a reference, and ask the author before reusing the design.
Can I test firmware for the Esp32 PD without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.
Similar boards
ESP32
OSO-BOOK-B1
joeycastillo
85 × 115 mm65 parts2LCC-BY-SA-4.08.1kESP32
Powertrain
byrantech
64 × 45.4 mm171 parts4LMIT4.3kESP32
Badge
atopile
56.3 × 39 mm239 parts4LMIT4.0kESP32
Esp32 minimal
atopile
36.2 × 26.8 mm20 parts2LMIT4.0kESP32
Controller
StuckAtPrototype
29 × 74 mm58 parts4LApache-2.03.8kESP32
Racer
StuckAtPrototype
36 × 50.2 mm70 parts4LApache-2.03.8k