Ninepin ux

jusii·ninepin-ux·hardware/rev7.1/ninepin-ux-rev7.1.kicad_pcb

Ninepin ux PCB layout, top view — open source RP2040/RP2350 board by jusii

About the Ninepin ux PCB

Ninepin ux is an open source RP2040/RP2350 PCB design by jusii, published on GitHub under the EPL-2.0 license. It is a 4-layer board measuring 100 × 62 mm, with 128 components from 54 distinct parts.

Its main chip is the RP2350A, from the RP2040/RP2350 family. Other key parts include the USBLC6-2SC6, TLV75733PDRVR, SN74CBTD3861DBQR, W25Q128JVSIQ and Raspberry Pi RM2. By type, the board carries 35 capacitors, 35 resistors, 27 diodes, 10 ICs, 9 connectors and 3 transistors.

It belongs with the retro computing, keyboards and iot & wireless designs in this gallery.

From the project

USB and Bluetooth HID bridge for retro computers: Amiga keyboard and DE9 ports, C64, USB device for C64 Ultimate. RP2350 board, firmware and case. Based on borb/amigahid-pico.

rev7 plus U11, a TLV803S reset supervisor on RUN. Same firmware, outline, connectors, case (../case/) and hand-fitted parts as rev7 (tag hw/ux-rev7). Ordering and assembly: doc/build.md.

U11 TLV803SDBZR (LCSC C132016) + C40 100 nF, south of the OLED. U11 holds RUN low until 3V3 has been above 2.93 V for 200 ms, and again whenever 3V3 sags below that: no more cold-plug BOOTSEL. Open drain, wired-OR with SW2 on runsw. New copper is route.py block 5 only. R70/R71 use C25190, the same 27R as R57/R58. L1 is the Abracon AOTA-B201610S3R3-101-T the land was drawn for. fab/makefab.py: JLC rotation…

Main components on the Ninepin ux

Ninepin ux bill of materials (BOM)

128 components, 54 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
RP2350A
U1
2
USBLC6-2SC6
U2, U4
1
TLV75733PDRVR
U3
2
SN74CBTD3861DBQR
U6, U7
1
W25Q128JVSIQ
U8
1
Raspberry Pi RM2
RM2
U9
1
TCA9554PWR
U10
1
TLV803SDBZR
U11
1
2N7002
Q1
2
BSS138
Q2, Q3
1
ABM8-272-T3
12MHz
Y1
1
C492407
A500 KBD OUT
J1
1
C2937625
SWD
J2
1
PM254-1-04-Z-8.5
OLED
J3
1
Molex 676432910
USB-A HOST
J4
1
BOOMELE 2.54-2*3P
ENCODER
J7
1
C492407
A500 KBD IN
J8
1
CUI MD-60S
KBD OUT (to Amiga)
J10
1
CUI MD-60S
KBD IN (from keyboard)
J12
1
GCT USB4105-GF-A-120
USB-C
J13
Show 34 more
QtyPartRefs
1
MF-MSMF075-2
750mA
F1
2
MF-MSMF050-2
500mA
F2, F3
1
C&K PTS645VK392LFS
BOOT
SW1
1
C&K PTS645VK392LFS
RESET
SW2
1
WS2812B-2020
LED1
3
SS34
D1, D2, D3
3
B5819W
D4, D5, D6
14
PESD5V0S1BA
D10, D11, D12, D20, D21, D22, D23, D24 +6
7
PESD5V0S1BL,315
PESD5V0S1BL
D13, D14, D15, D16, D17, D18, D19
1
BLM18AG601SN1D
600R@100MHz
FB1
1
AOTA-B201610S3R3-101-T
3.3uH
L1
1
22UF
22uF
C1
4
10UF
10uF
C2, C6, C10, C14
13
100NF
100nF
C3, C5, C7, C11, C12, C13, C23, C24 +5
1
EEEFKC151XAP
150uF
C4
3
1UF
1uF
C8, C9, C31
1
4.7UF
4.7uF
C20
6
100NF
100nF
C21, C22, C25, C30, C39, C40
2
4.7UF
4.7uF
C29, C38
2
15PF
15pF
C33, C34
1
4.7UF
4.7uF
C35
1
4.7UF
4.7uF
C37
3
4.7K
4.7k
R41, R42, R68
2
5.1K
5.1k
R43, R44
2
470
R45, R55
2
100K
100k
R46, R47
5
1k
R49, R52, R53, R54, R60
2
33
R50, R59
2
10K
10k
R56, R69
4
27
R57, R58, R70, R71
7
10K
10k
R61, R62, R63, R64, R65, R66, R67
2
15K
15k
R72, R73
3
4X10K
4x10k
RN1, RN2, RN4
1
4X10K
4x10k
RN3

Ninepin ux design files

The KiCad project lives in the jusii/ninepin-ux repository on GitHub; these links point at the commit this page was built from.

Ninepin ux: common questions

What microcontroller does the Ninepin ux use?

The Ninepin ux is built around the RP2350A, from the RP2040/RP2350 family.

How big is the Ninepin ux PCB?

The Ninepin ux measures 100 × 62 mm, has 4 copper layers and is 1.6 mm thick.

How many components are on the Ninepin ux?

128 components, from 54 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Ninepin ux design files?

From the jusii/ninepin-ux repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Ninepin ux design in my own project?

It is published under EPL-2.0, which limits how it may be reused; read the license before building on it.

Can I test firmware for the Ninepin ux without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug RP2040/RP2350 firmware against it before you order a PCB.

Similar boards