Base

kanisakhpara-devs·holographic-hullabaloo·pcb/base/base.kicad_pcb

Base PCB layout, top view — open source ESP32 board by kanisakhpara-devs

About the Base PCB

Base is an open source ESP32 PCB design by kanisakhpara-devs, published on GitHub under the MIT license. It is a 2-layer board measuring 96 × 99.5 mm, with 41 components from 34 distinct parts.

Its main chip is the ESP32-S3-WROOM-1-N8, from the ESP32 family. Other key parts include the USBLC6-2SC6, AMS1117-3.3 and MAX98357AETE+T. By type, the board carries 11 connectors, 11 capacitors, 8 resistors, 4 ICs, 4 diodes and 2 switches.

It belongs with the audio, displays & leds and power & battery designs in this gallery.

From the project

A POV holographic AI assistant desk viewer. Largely in dev phase for now, open sourced for the 'Fallen' event by Hackclub. Feel free to check it out, download it, or contact me with errors or discrepancies found!

I understand your possibly dire confusion, so I'll try my best to explain it in the simplest way possible. Have you ever seen those LED fans which are all over Insta? They spin, to create an image.

The problem, however with those, is that they can only be viewed from one side, and properly from only one angle. Instead of engineering the solution, they are simply stuck on your wall, so it is only possible to view it from that exact point. Sometimes the best solutions are the most simple ones. Not in this case.

Base, from the project README
From the project README

Main components on the Base

Base bill of materials (BOM)

41 components, 34 distinct parts — part numbers from the project's BOM.

QtyPartRefs
1
ESP32-S3-WROOM-1-N8
U1
1
USBLC6-2SC6
U2
1
AMS1117-3.3
U3
1
MAX98357AETE+T
U4
1
AO4406A
Q1
1
C2765186
USB-C
J1
1
Buck module
J2
1
12V IN
J3
1
Motor
J4
1
Coil TX 12V
J5
1
C295747
Speaker 4R 3W
J6
1
INMP441 mic
J7
1
ToF front
J8
1
ToF back
J9
1
Talk button
J10
1
UART debug
J11
1
C318884
RESET
SW1
1
C318884
BOOT
SW2
1
SS34
D1
1
C8678
SS34 flyback
D2
Show 14 more
QtyPartRefs
1
C2286
Red
D3
1
C8678
SS34 buck OR
D4
2
22UF
22uF
C1, C6
3
100NF
100nF
C2, C4, C9
1
1UF
1uF
C3
2
10UF
10uF
C5, C8
2
C45783
22uF 25V
C10, C11
1
C1984855
470uF 25V
C12
2
10K
10k
R1, R2
2
5.1K
5.1k
R3, R4
1
33R
R5
1
100K
100k
R6
1
1M
R7
1
1k
R10

Base design files

The KiCad project lives in the kanisakhpara-devs/holographic-hullabaloo repository on GitHub; these links point at the commit this page was built from.

Base: common questions

What microcontroller does the Base use?

The Base is built around the ESP32-S3-WROOM-1-N8, from the ESP32 family.

How big is the Base PCB?

The Base measures 96 × 99.5 mm, has 2 copper layers and is 1.6 mm thick.

How many components are on the Base?

41 components, from 34 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.

Where can I download the Base design files?

From the kanisakhpara-devs/holographic-hullabaloo repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.

Can I use the Base design in my own project?

Yes, under the terms of its MIT license, which kanisakhpara-devs chose for the repository.

Can I test firmware for the Base without the hardware?

Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug ESP32 firmware against it before you order a PCB.

More boards in holographic-hullabaloo

Similar boards