Tk1
kr-Eliza·tkey-open-hardware-reproduction·hardware/voltera-prototype/tk1.kicad_pcb
About the Tk1 PCB
Tk1 is an open source FPGA PCB design by kr-Eliza, published on GitHub under the CERN-OHL-S-2.0 license. It is a 2-layer board measuring 83 × 58 mm, with 44 components from 19 distinct parts.
Its main chip is the ICE40UP5K-SG48ITR, from the FPGA family. Other key parts include the MCP1824T-2502EOT, MIC5258-1.2YM5, CH552E, USBLC6-2SC6 and W25Q80DVUXIE. By type, the board carries 18 capacitors, 13 resistors, 7 ICs, 4 diodes, 1 connector and 1 inductor.
From the project
Reproducing the Tillitis TKey open hardware security key: 2-layer hand-solderable PCB, lab assembly and bring-up, Voltera prototype, SBOM
Most hardware security keys are closed: their schematics, firmware and key storage cannot be inspected, so users have to trust the vendor. The TKey takes the opposite approach. Its hardware (a Lattice iCE40UP5K FPGA running a small RISC-V core, plus a CH552 USB controller) and its firmware are fully open, which makes it a good subject for a reproduction and hardening project:

Main components on the Tk1
Tk1 bill of materials (BOM)
44 components, 19 distinct parts — part numbers from the project's BOM.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP1824T-2502EOT Microchip | SOT-23-5 | U1 |
| 1 | MIC5258-1.2YM5 Micrel Inc. | SOT-23-5 | U2 |
| 1 | CH552E WCH | MSOP-10_3x3mm_P0.5mm | U3 |
| 1 | USBLC6-2SC6 ST | SOT-23-6 | U5 |
| 1 | ICE40UP5K-SG48ITR Lattice | QFN-48-1EP_7x7mm_P0.5mm_EP5.6x5.6mm | U6 |
| 1 | W25Q80DVUXIE SOIC-8 Winbond Electronics | SOIC-8_3.9x4.9mm_P1.27mm | U8 |
| 1 | NCP752BSN33T1G onsemi | NCP752BSN33T1G | U9 |
| 1 | USB_A | USB_A_Kycon_KUSBX-AS1N-B_Horizontal | J1 |
| 1 | NCD0402B1 0402 indicator LED, blue Foshan NationStar | LED_0805_2012Metric | D1 |
| 1 | LEDred | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D2 |
| 1 | LEDgreen | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D3 |
| 1 | LEDblue | LED_0805_2012Metric_Pad1.15x1.40mm_HandSolder | D4 |
| 1 | BLM18KG300TN1D Murata | Ferritbead_0603_1608Metric | FB3 |
| 7 | 10UF 10uF Any/not critical | C_0805_2012Metric | C1, C2, C3, C4, C5, C6, C25 |
| 10 | 0.10UF 0.10uF Any/not critical | C_0805_2012Metric | C7, C13, C16, C17, C18, C19, C20, C21 +2 |
| 1 | 0.10uF Any/not critical | C_0805_2012Metric | C26 |
| 3 | 10k Any/not critical | R_0805_2012Metric | R1, R2, R22 |
| 4 | 1k Any/not critical | R_0805_2012Metric | R3, R16, R17, R18 |
| 6 | 10K 10k Any/not critical | R_0805_2012Metric | R19, R20, R23, R24, R25, R26 |
Tk1 design files
The KiCad project lives in the kr-Eliza/tkey-open-hardware-reproduction repository on GitHub; these links point at the commit this page was built from.
Tk1: common questions
What microcontroller does the Tk1 use?
The Tk1 is built around the ICE40UP5K-SG48ITR, from the FPGA family.
How big is the Tk1 PCB?
The Tk1 measures 83 × 58 mm, has 2 copper layers and is 0.8 mm thick.
How many components are on the Tk1?
44 components, from 19 distinct parts, with part numbers taken from the project's own BOM. The full bill of materials is listed on this page.
Where can I download the Tk1 design files?
From the kr-Eliza/tkey-open-hardware-reproduction repository on GitHub, which has the KiCad layout, the schematic and the BOM; the links under Design files point to each one.
Can I use the Tk1 design in my own project?
Yes, under the terms of its CERN-OHL-S-2.0 license, which kr-Eliza chose for the repository.
Can I test firmware for the Tk1 without the hardware?
Yes. HardLabs builds a simulation of the board from its netlist and BOM, so you can run and debug FPGA firmware against it before you order a PCB.
More boards in tkey-open-hardware-reproduction
Similar boards
FPGA
Base board
GlasgowEmbedded
80 × 49 mm222 parts4L0BSD2.2kFPGA
Thunderscope Rev5.3
EEVengers
122.5 × 103.5 mm817 parts6LMIT1.3kFPGA
Usb sniffer
ataradov
58.2 × 38.1 mm86 parts2LBSD-3-Clause1.3kFPGA
Tomu, I'm
theacodes
13 × 9.4 mm40 parts4LMIT1.1kFPGA
Icepi zero
cheyao
65 × 30 mm143 parts4LSHL-2.1865FPGA
Gcvideo
ikorb
49 × 30 mm44 parts4LNo license765