8 open source boards using the CH552E
Real designs built with the CH552E, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
STM32
F303k8-led matrix-4layer
Netetra
35 × 25 mm98 parts4LNo license0FPGA
PCB Voltera
Michaelf09
83 × 58 mm46 parts2LNo license0FPGA
Tk1
kr-Eliza
83 × 58 mm44 parts2LCERN-OHL-S-2.00WCH CH32/CH55x
Ch552e
nilslmm
34 × 8.4 mm10 parts2LNo license0FPGA
Mta1-usb v1
tillitis
28.4 × 13.5 mm47 parts4LCERN-OHL-S-2.03FPGA
Tk1-0805
kr-Eliza
57.6 × 39.8 mm43 parts2LCERN-OHL-S-2.00FPGA
Tk1
tillitis
28.6 × 13.9 mm46 parts4LCERN-OHL-S-2.03WCH CH32/CH55x
Ch552-daplink vcut
Netetra
22 × 11.5 mm21 parts2LNo license0
How designs wire the CH552E
Read from the KiCad layouts of 5 open source designs, one per repository: what each pin of the CH552E connects to, and the resistors, capacitors and other passives placed on it.
- The RST pin is left unconnected on 5 of 5 designs.
- The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 10 µF).
- The V33 pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 10 µF).
- The UDP(P3.6) pin has a series resistor on 2 of 5 designs, most often 10 kΩ (then 1.5 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| RSTpin 5 | Connected to: Not connected 100% | — |
| UDP(P3.6)pin 6 | Connected to: USBLC6-2SC6 60%, a connector 40% |
|
| GNDpin 8 | Connected to: GND 80% · a signal 20% | — |
| VCCpin 9 | Connected to: 3.3V 80% · a signal 20% |
|
| V33pin 10 | Connected to: 3.3V 80% · a signal 20% |
|
5 more pins vary from design to design. Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Mta1-usb v1 by tillitis, Tk1 by kr-Eliza, PCB Voltera by Michaelf09 and Ch552-daplink vcut by Netetra.
The CH552E in open source designs
The gallery holds 8 open source boards using the CH552E from 5 GitHub repositories; a typical one measures about 34.5 × 19.4 mm and carries around 45 components.
63% are two-layer designs, the rest use four layers or more, and 50% carry an open source license.
The most starred is Mta1-usb v1 by tillitis.
Parts used alongside the CH552E
Microcontrollers on boards using the CH552E
What boards using the CH552E are built for
CH552E: common questions
Where can I find a CH552E reference design?
Each of the 8 boards on this page is a real design using the CH552E. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the CH552E RST pin connected?
The RST pin is left unconnected on 5 of 5 designs. Counted from the KiCad layouts of 5 open source designs using the CH552E.
What decoupling capacitors do designs use on the CH552E VCC pin?
The VCC pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the CH552E.
What decoupling capacitors do designs use on the CH552E V33 pin?
The V33 pin has a decoupling capacitor on 3 of 5 designs, most often 100 nF (then 10 µF). Counted from the KiCad layouts of 5 open source designs using the CH552E.
What parts are used alongside the CH552E?
The USBLC6-2SC6, ICE40UP5K-SG48ITR, MCP1824T-2502EOT, MIC5258-1.2YM5 and NCP752BSN33T1G appear in the most repositories here.
Which microcontrollers do boards using the CH552E use?
Most are built on FPGA (5), WCH CH32/CH55x (2) and STM32 (1).
How big is a typical board using the CH552E?
The median is 34.5 × 19.4 mm, and 63% are two-layer designs.
What is the most popular open source board using the CH552E?
By GitHub stars, Mta1-usb v1 by tillitis, with 3 stars.
Can I simulate one of these boards using the CH552E before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.