Water saturation
laoeked1111·water-saturation
About the Water saturation PCB
Water saturation is an open source PCB design by laoeked1111, published on GitHub. It is a 2-layer board measuring 52.5 × 24.8 mm, with 28 components from 24 distinct parts.
Other key parts include the MCP1640Bx-xCHY, LM358, NE555D and LM311. By type, the board carries 12 resistors, 9 capacitors, 4 ICs, 1 microphone, 1 diode and 1 inductor.
It belongs with the power & battery and sensors designs in this gallery.
From the project
Battery-powered water saturation sensor
A PCB for a battery-powered ultrasonic sensor for detecting the water saturation level of cloth based on attenuation of the ultrasound signal.
The system runs on a 3.3V coin cell battery, which is boosted to 5V to power the ICs. A 555 timer drives the ultrasound transducer, and a microphone captures the ultrasound signal. The collected signal is amplified and filtered, then passed through a comparator to produce a PWM waveform that drives a LED. The LED lights up when the signal is low, signallying high attenuation due to water saturation, and is dim/off when the signal is high.

Main components on the Water saturation
Water saturation bill of materials (BOM)
28 components, 24 distinct parts.
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | MCP1640Bx-xCHY | SOT-23-6 | U1 |
| 1 | LM358 | SOIC-8_3.9x4.9mm_P1.27mm | U2 |
| 1 | NE555D | SOIC-8_3.9x4.9mm_P1.27mm | U3 |
| 1 | LM311 | SOIC-8_3.9x4.9mm_P1.27mm | U4 |
| 1 | Microphone | PinHeader_1x03_P2.54mm_Vertical_SMD_Pin1Left | MK1 |
| 1 | 1N4148WT | D_SOD-523 | D1 |
| 1 | MLZ1608M4R7WT000 | IND_1608_TDK | L1 |
| 1 | 1uF | C_0603_1608Metric | C1 |
| 1 | 4.7uF | C_0603_1608Metric | C2 |
| 1 | 22nF | C_0603_1608Metric | C3 |
| 1 | 10uF | C_0603_1608Metric | C4 |
| 3 | 0.1uF | C_0603_1608Metric | C5, C6, C8 |
| 1 | 6.8nF | C_0603_1608Metric | C7 |
| 1 | 10nF | C_0603_1608Metric | C9 |
| 2 | 1kR | R_0603_1608Metric | R1, R3 |
| 1 | 100kR | R_0603_1608Metric | R2 |
| 1 | 220kR | R_0603_1608Metric | R4 |
| 1 | 100R | R_0603_1608Metric | R5 |
| 1 | 976kR | R_0603_1608Metric | R6 |
| 1 | 309kR | R_0603_1608Metric | R7 |
Show 4 more
| Qty | Part | Footprint | Refs |
|---|---|---|---|
| 1 | 470R | R_0603_1608Metric | R8 |
| 1 | 1.5kR | R_0603_1608Metric | R9 |
| 1 | 620R | R_0603_1608Metric | R10 |
| 2 | 110R | R_0603_1608Metric | R11, R12 |
Water saturation design files
The KiCad project lives in the laoeked1111/water-saturation repository on GitHub; these links point at the commit this page was built from.
- Layoutsmart-diaper.kicad_pcb
- Schematicsmart-diaper.kicad_sch
Water saturation: common questions
How big is the Water saturation PCB?
The Water saturation measures 52.5 × 24.8 mm, has 2 copper layers and is 1.6 mm thick.
How many components are on the Water saturation?
28 components, from 24 distinct parts. The full bill of materials is listed on this page.
Where can I download the Water saturation design files?
From the laoeked1111/water-saturation repository on GitHub, which has the KiCad layout and the schematic; the links under Design files point to each one.
Can I use the Water saturation design in my own project?
The repository has no license, so all rights stay with laoeked1111. Use it as a reference, and ask the author before reusing the design.
Similar boards
Sensor smd
scottbez1
40 × 20 mm5 parts2LApache-2.04.2kSensors
StuckAtPrototype
15.2 × 9 mm14 parts4LApache-2.03.8kEinkPDA screen
TalismanDesign
95 × 54 mm27 parts2LApache-2.02.0kStack chan
stack-chan
50 × 50 mm33 parts2LApache-2.01.7kDisplay Carrier
AxxAxx
35.6 × 58.2 mm5 parts2LGPL-3.01.7kMicrophone
Mentra-Community
5.5 × 6.1 mm6 parts2LMIT1.2k