69 open source boards using the LM311
Real designs built with the LM311, from public GitHub projects: a quick way to see how others power, decouple and connect it. Each board comes with its KiCad files, full parts list and a render — and you can simulate its firmware on HardLabs.
Vco core
shmoergh
58 × 110 mm116 parts2LNo license219Core
shmoergh
215 × 100 mm285 parts2LNo license124Zoxnoxious Z5524 (SSI2130/AS3394)
brer-rabbit
80 × 80 mm222 parts4LGPL-3.068RP2040/RP2350
Multislope-3I
NNNILabs
100 × 74 mm124 parts4LMIT43ESP8266
Stargate
leomanes
335 × 218.6 mm274 parts2LGPL-3.018Junior interface
laurent-fr
217.2 × 113 mm116 parts2LCC-BY-NC-4.014Panning Mixer
powsplatboom
243.8 × 100 mm633 parts4LNo license11MICRO-OX Main VCO board
JordanAceto
133.9 × 165.1 mm280 parts4LCC-BY-4.08Edm power board
strombom
240 × 80 mm150 parts4LNo license7Sstc
hnaderi
100 × 80 mm102 parts2LCC0-1.03AVR/Arduino
RelayTrackerController
bask185
54 × 94.5 mm86 parts2LNo license3Raspberry Pi
Tetra Link boardIWQ
f1iwq2
85.2 × 55.4 mm70 parts2LNo license3RP2040/RP2350
Karabas go
andykarpov
101.6 × 147.3 mm279 parts4LCC-BY-NC-4.02JFF
herraa1
250 × 150 mm132 parts2LGPL-3.02RP2040/RP2350
Karabas Go Mini
andykarpov
70 × 69.8 mm205 parts4LCC-BY-NC-4.01ESP32
LV PCB
luftaquila
293.1 × 125.3 mm159 parts2LNo license1AVR/Arduino
PlacaMotores
Robot-Sumo
104.5 × 81.9 mm52 parts2LNo license1Easy-Add on-Projects for-Amstrad-CPC
BrettHallen
53 × 38 mm21 parts2LNo license1MusicBrain VCF8-kern - 8x multimode VCF
MarkWestbroek
110 × 92 mm412 parts4LMIT0Analog via
starlingcode
213.5 × 128.5 mm269 parts4LCC-BY-NC-4.00Raspberry Pi
Vinyl adc rev d
MadsRudolph
140 × 136 mm177 parts4LNo license0PIC
ATE-PCB-DESIGN
muhin19
147 × 78.5 mm110 parts2LNo license0EurorackVco
thismatters
50.5 × 128.5 mm103 parts2LNo license0ESP32
GOONER2000
avi-guha
142 × 110 mm99 parts4LNo license0Drsstc
domergan
64.8 × 76.2 mm69 parts2LNo license0Cdipannoucer
buelowp
105.7 × 60.2 mm53 parts2LMIT0RM28 RTML
RensselaerMotorsport
71.6 × 42.7 mm38 parts2LBSD-3-Clause0ESP32
Geiger
KrzysztofMathiak
117 × 74 mm38 parts2LNo license0Water saturation
laoeked1111
52.5 × 24.8 mm28 parts2LNo license0Rc debouncing
enph253-2025-team5
58.4 × 31.8 mm18 parts2LGPL-3.00- schematic only · 36 partsAVR/Arduino
Breadboard-Power-Supply
leboeuf-dup
36 parts2LNo license0 Ud29
profdc9
97.5 × 97.5 mm123 parts2LNo license56Vm113-effects
mirdej
58 × 71 mm126 parts4LNo license23Junior computer
laurent-fr
217.2 × 113 mm80 parts2LCC-BY-NC-4.014Spring Reverb
powsplatboom
170 × 100 mm313 parts4LNo license11STM32
Modulation board
JordanAceto
111.8 × 165.1 mm231 parts4LCC-BY-4.08
How designs wire the LM311
Read from the KiCad layouts of 39 open source designs, one per repository: what each pin of the LM311 connects to, and the resistors, capacitors and other passives placed on it.
- The BAL pin is left unconnected on 35 of 39 designs (a signal on 3).
- The STRB pin is left unconnected on 32 of 39 designs (a signal on 5).
- Pin 7 has a pull-up to 5V on 26 of 39 designs, most often 1 kΩ (then 10 kΩ).
- The + pin has a series resistor on 22 of 39 designs, most often 1 MΩ (then 100 kΩ).
| Pin | Connected to | Parts on the pin |
|---|---|---|
| GNDpin 1 | Connected to: GND 74% · a signal 15% | — |
| +pin 2 | Connected to: Signal 90% |
|
| -pin 3 | Connected to: Signal 95% |
|
| V-pin 4 | Connected to: GND 64% · -12V 18% | — |
| BALpin 5 | Connected to: Not connected 90% | — |
| STRBpin 6 | Connected to: Not connected 82% | — |
| Pin 7 | Connected to: A connector 33% |
|
| V+pin 8 | Connected to: 12V 92% |
|
Connections count pins, parts count designs; values in brackets are how many parts had that value. Designs read include Vco core by shmoergh, Core by shmoergh, Z3340 VCO by brer-rabbit and TSAL-HVM by michaelruppe.
The LM311 in open source designs
The gallery holds 69 open source boards using the LM311 from 41 GitHub repositories; a typical one measures about 100.8 × 97.5 mm and carries around 95 components.
71% are two-layer designs, the rest use four layers or more, and 28% carry an open source license.
The most starred is Vco core by shmoergh.
Parts used alongside the LM311
Microcontrollers on boards using the LM311
What boards using the LM311 are built for
LM311: common questions
Where can I find a LM311 reference design?
Each of the 69 boards on this page is a real design using the LM311. Open one to see how it is wired up, with the full BOM, a render of the layout and links to its KiCad files.
How is the LM311 BAL pin connected?
The BAL pin is left unconnected on 35 of 39 designs (a signal on 3). Counted from the KiCad layouts of 39 open source designs using the LM311.
How is the LM311 STRB pin connected?
The STRB pin is left unconnected on 32 of 39 designs (a signal on 5). Counted from the KiCad layouts of 39 open source designs using the LM311.
What pull-up resistor is used on the LM311 pin 7?
Pin 7 has a pull-up to 5V on 26 of 39 designs, most often 1 kΩ (then 10 kΩ). Counted from the KiCad layouts of 39 open source designs using the LM311.
What parts are used alongside the LM311?
The 74HC74, 74HC14, TL072, TL074 and 74HC08 appear in the most repositories here.
Which microcontrollers do boards using the LM311 use?
Most are built on AVR/Arduino (8), ESP32 (4), Raspberry Pi (4) and RP2040/RP2350 (3).
How big is a typical board using the LM311?
The median is 100.8 × 97.5 mm, and 71% are two-layer designs.
What is the most popular open source board using the LM311?
By GitHub stars, Vco core by shmoergh, with 219 stars.
Can I simulate one of these boards using the LM311 before building it?
Yes. HardLabs turns a board's netlist and BOM into a working simulation, so you can boot and test firmware against it with no hardware on your desk.